Launch X-431TOP Скачать руководство пользователя страница 1

LAUNCH                                                                                                                      X-431TOP User

s Manual 

 

Trademark Information 

 

LAUNCH  is  a  registered  trademark  of  LAUNCH 
TECH. CO., LTD. (short for LAUNCH ) in China 
and  other  countries.  All  other  LAUNCH 
trademarks, service marks, domain names, logos, 
and  company  names  referred  to  in  this  manual 
are  either  trademarks,  registered  trademarks, 
service  marks,  domain  names,  logos,  company 
names  of  or  are  otherwise  the  property  of 
LAUNCH or its affiliates. In countries where any 
of  the  LAUNCH  trademarks,  service  marks, 
domain  names,  logos  and  company  names  are 
not  registered,  LAUNCH  claims  other  rights 
associated with unregistered trademarks, service 
marks,  domain  names,  logos,  and  company 
names.  Other  products  or  company  names 
referred to in this manual may be trademarks of 
their  respective  owners.  You  may  not  use  any 
trademark, service mark, domain name, logo, or 
company  name  of  LAUNCH  or  any  third  party 
without  permission  from  the  owner  of  the 
applicable  trademark,  service  mark,  domain 
name, logo, or company name. You may contact 
LAUNCH  by  visiting  Launch  at  http://  www. 
cnlaunch.  com,  or  writing  to  LAUNCH,  Xinyang 
Building,  Bagua  4th  Road,  Shenzhen, 
Guangdong Province, P. R. C., to request written 
permission  to  use  Materials  on  this  manual  for 
purposes or for all other questions relating to this 
manual.   

Copyright Information 

 

Copyright 

©

 2006 by LAUNCH TECH. CO., LTD. 

All  rights  reserved.  No  part  of  this  publication 
may be reproduced, stored in a retrieval system, 
or  transmitted  in  any  form  or  by  any  means, 
electronic,  mechanical,  photocopying,  recording 
or otherwise, without the prior written permission 
of LAUNCH. The information contained herein is 
designed only for the use of this unit. LAUNCH is 
not responsible for any use of this information as 
applied to other units.   
Neither  LAUNCH  nor  its  affiliates  shall  be  liable 
to  the  purchaser  of  this  unit  or  third  parties  for 

damages, losses, costs, or expenses incurred by 
purchaser or third parties as a result of: accident, 
misuse,  or  abuse  of  this  unit,  or  unauthorized 
modifications,  repairs,  or  alterations  to  this  unit, 
or  failure  to  strictly  comply  with  LAUNCH 
operating and maintenance instructions. 

 

LAUNCH shall not be liable for any damages or 
problems arising from the use of any options or 
any  consumable  products  other  than  those 
designated  as  Original  LAUNCH  Products  or 
LAUNCH Approved Products by LAUNCH. 

General Notice 

 

l

 

Other  product  names  used  herein  are  for 

identification  purposes  only  and  may  be 
trademarks  of  their  respective  owners. 
LAUNCH  disclaims  any  and  all  rights  in 
those marks.   

l

 

There  is  a  possibility  that  this  unit  is 
inapplicable  to  some  of  the  vehicle 
models or systems listed in the diagnosis 
section  due  to  different  countries,  areas, 
and/or  years.  Do  not  hesitate  to  contact 
LAUNCH  if  you  come  across  such 
questions. We are to help you solve the 
problem as soon as possible. 

Disclaimer 

 

l

 

To  take  full  advantage  of  the  unit,  you 
should be familiar with the engine. 

l

 

All 

information, 

illustrations, 

and 

specifications  contained  in  this  manual 
are  based  on  the  latest  information 
available  at  the  time  of  publication.  The 
right is reserved to make change at any 
time without notice.   

 
 
 
 
 
 

 

Содержание X-431TOP










































Отзывы: