Lauda LRZ 921 Скачать руководство пользователя страница 5

Страница: 5 / 40

1 General

Many types of LAUDA constant temperature equipment have vacant

module slots for installing additional interfaces. The number, size and

arrangement of the module slots vary depending on the device and are

described in the operating manual accompanying the constant temperature

equipment. Two additional module slots available as accessories can be fitted

to a LiBus module box, which is then connected as an external casing to the

LiBus interface on the constant temperature equipment.

This operating manual describes how to install and configure the Ethernet

USB interface module (catalog no. LRZ 921).
Constant temperature equipment can be connected to a PC or network

via the Ethernet interface and controlled from there using the LAUDA

command set. The interface functions provided for this purpose are

described in chapters and .
The two USB interfaces are intended for future expansion and do not cur-

rently have any function.

1.1

Intended use

The interface module can only be operated as intended and under the

conditions specified in this operating manual.
The interface module is an accessory that increases the connections options

of LAUDA constant temperature equipment. It may only be installed in con-

stant temperature equipment that supports the interface provided. Refer to

the chapter "Compatibility” in this operating manual for a list of compatible

product lines.
Operation of the interface module is also permitted in combination with the

LiBus module box (LAUDA catalog no. LCZ 9727). This operating manual

also contains a description of how to install and connect up the module box.



Operation after incomplete assembly



Operation on incompatible constant temperature equipment



Operation using cables or connections that are defective or do not

confirm to standards

1.2

Compatibility

The interface module is available as an accessory for the following LAUDA

product lines:



ECO



Proline



Variocool, not compatible with Variocool NRTL



Integral XT, not compatible with Integral IN

Operating interfaces of the same type:
Only one Ethernet interface can be used for each item of constant

temperature equipment.

Reasonably foreseeable improper use

V2R4

Interface module LRZ 921

5 / 39

Содержание LRZ 921









































Результаты поиска

Содержание LRZ 921

Отзывы:

Похожие инструкции для LRZ 921

Бренды по названию

Популярные бренды

Lauda LRZ 921, Руководство по эксплуатации

Результаты поиска

Содержание LRZ 921

Отзывы:

Похожие инструкции для LRZ 921

Бренды по названию

Популярные бренды