F 7.3.12 - 0312
Data Sheets are subject to change without notice. For latest revision, check our website at www.laticrete.com.
DS-034.0-0412
1. PRODUCT NAME
LATICRETE
®
Hydro Ban
®
Linear Drain
2. MANUFACTURER
LATICRETE International, Inc.
1 LATICRETE Park North
Bethany, CT 06524-3423 USA
Telephone: +1.203.393.0010, ext. 235
Toll Free:
1.800.243.4788, ext. 235
Fax:
+1.203.393.1684
Internet:
www.laticrete.com
3. PRODUCT DESCRIPTION
LATICRETE Hydro Ban Linear Drain is a low profile linear floor drain
specifically designed for bonded waterproofing installations with
LATICRETE Hydro Ban waterproofing membrane. LATICRETE
Hydro Ban Linear Drain allows for the use of large format tile or stone
installations in a shower with a single plane slope to the drain. The
LATICRETE Hydro Ban Linear Drain can be installed near the wall or
at medial locations in a variety of areas requiring waterproof
applications.
Uses
Interior or exterior
Showers
Industrial, commercial and residential bathrooms and laundries
Kitchens and food processing areas
Terraces, decks and balconies
Advantages
Single slope to drain
Allows for use of large format tile
Tile in grate available to match floor tile
Eliminates pre-slope and primary shower pan
For a faster installation
Made from heavy duty 304 stainless steel provides for long
lasting performance
LATICRETE Hydro Ban waterproof membrane bonds directly to
stainless steel flange edge allowing for faster, easier installation
Suitable Substrates
Concrete
Exterior Glue Plywood (Interior Only)
Cement backer board
Cement mortar beds
Packaging
The LATICRETE Hydro Ban Linear Drain is a two piece drain with a
trough and removable grate. Available in five lengths and two grate
configurations: offset oval in brushed stainless steel and a tile in tray.
The LATICRETE Hydro Ban Linear Drains are available in 24"(61
cm), 32"(81 cm), 36"(91 cm), 48"(122 cm) and 60"(152 cm) lengths.
Limitations
Adhesives/mastics, mortars and grouts for ceramic tile,
pavers, brick and stone are not replacements for waterproofing
membranes. When a waterproofing membrane is required, use
a LATICRETE Hydro Ban (see Section 10 FILING SYSTEMS).
Note:
Surfaces must be structurally sound, stable and rigid
enough to support ceramic/stone tile, thin brick and similar
finishes. Substrate deflection under all live, dead and impact
loads, including concentrated loads, must not exceed L/360 for
thin bed ceramic tile/brick installations or L/480 for thin bed
stone installations where L=span length.
Cautions
Consult MSDS for more safety information.
During cold weather, protect finished work from traffic until fully
cured.
All stainless steel surfaces must be clean and free of any dirt,
oil, grease and fingerprints prior to coating with LATICRETE
Hydro Ban.
4. TECHNICAL DATA
Applicable Standard
Code approval per ASME A 112.18-2/CSA B125.2.05 (US and
Canada)
Working Properties
The LATICRETE Hydro Ban Linear Drain series installs per IAPMO
IGC 195-2010. Waterproof using LATICRETE Hydro Ban per TCNA
B422.
5. INSTALLATION
Surface Preparation
All surfaces should be between 40°F (4°C) and 90°F (32°C) and
structurally sound, clean and free of all dirt, oil, grease, laitance,
paint, concrete sealers or curing compounds. Dry dusty concrete
slabs or masonry should be dampened and excess water swept off.
Hydro Ban
®
Linear Drain
DS-034.0-0412
