background image

 

 

PayClock, Lathem and the Lathem logo

 are registered trademarks of Lathem Time Corporation. Other product names mentioned in 

this manual may be trademarks of their respective companies and are hereby acknowledged. 
 

Warning

: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s 

authority to operate the equipment. 
 

NOTICE:

 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 

of the FCC Rules

. These limits are designed to provide reasonable protection against harmful interference when the equipment is 

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructional manual, may cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference 
at his or her own expense. 
 

Shielded cables must be used with this unit to ensure compliance with the Class A FCC limits 
 

 

Содержание PC100-R






















Отзывы: