manualshive.com logo in svg

Laser Technology TruPulse 200L, Руководство пользователя

Поделиться
Скачать
Laser Technology TruPulse 200L Скачать руководство пользователя страница 12

Laser Technology, Inc. TruPulse 200L User's Manual 1

st

 Edition 

Page 8 

Buttons 

The TruPulse 200L has three buttons. With the TruPulse 200L in your right hand and 

looking through the eyepiece, 

 is located on top, near your index finger. 

 and 

  

are located on the left side of the instrument.  

 

Measurement Modes 

Powers ON the unit. 
Distance Measurement: fires the laser. 
Inclination: Release “locks” tilt sensor in (1) Height 
Measurement Mode and (2) Continuous Target Mode.

 

Height Routine 

(HD) Fires the laser. 

(INC) Release “locks” tilt sensor.

 

Target Modes 

System Setup Mode 

Selects option and returns to the Measurement Mode.

 

 

 

 

(UP)

 

Measurement Modes 

Press to scroll to the previous Measurement Mode.

 

Press-and-hold 4 seconds to access the Target Mode.

 

Height Routine 

Clears the last measurement and re-displays the previous 
prompt.

 

Target Modes 

System Setup Mode 

Press to scroll to the previous option. 

 

 

 

 

(DOWN)

 

Measurement Modes 

Press to scroll to the next Measurement Mode.

Press-and-hold 4 seconds to access the System Setup Mode.

 

Height Routine 

Exits the Height Routine.

Target Modes 

System Setup Mode 

Press to scroll to the next option. 

 

 

Powering OFF the TruPulse 200L 

To power OFF the unit, simultaneously press-and-hold 

 and 

 for 4 seconds.  

To conserve battery power, the TruPulse 200L powers itself OFF if no button presses  
are detected after 2 minutes. 

Содержание TruPulse 200L





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды