![background image](http://html1.mh-extra.com/html/larson-electronics/ledlb-4-ir/ledlb-4-ir_instruction-manual_3875882001.webp)
QUICK DISCONNECT
DEUTSCH CONNECTOR
LEDLB-4-IR
IR LED Light Emitter
12 watts - 4 LEDs - 90'L X 70'W Beam - 9-42 Volts DC
Instruction Manual
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE
LEDLB-4-IR
MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING:
MAKE SURE POWER IS TURNED
OFF
BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –
DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –
FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –
ALLOW FIXTURE TO COOL BEFORE SERVICING.
INFRARED LIGHT MAY CAUSE DAMAGE TO EYES
IN VERY INTENSE CONCENTRATIONS.
RISK OF EYE DAMAGE AT SHORT DISTANCES.
TURN LIGHT SOURCE OFF BEFORE SERVICING.
The Larson Electronics LEDLB-4-IR LED Light Bar offers high infrared light output and a compact profile combined with
versatile mounting and power options. This IP67 rated IR LED light bar is waterproof to one meter and produces 750
lumens of infrared light while drawing only 12 watts of power @1 amp from a 12 volt electrical system. This light can run
on any voltage from 9 to 42 volts and produces an infrared light beam that can only be seen through the use of night
vision goggles. 750Nm, 850Nm or 940Nm versions. This light provides a compact and powerful infrared lighting solution
that is ideal for use in commercial and industrial security applications as well as military environments.
Mounting
This fixture offers aluminum mounting blocks which slide within the
aluminum housing to allow users to adjust
their positioning to match
existing or user drilled mounting holes.
Each aluminum mounting
block has an integrated rubber bushing to absorb vibrations and
shocks. To secure the
lights in place, simply slide the mounting bolts
through the aluminum mounting block and rubber isolator, through
to
the mounting surface, then secure the bolt with a locking nut on the
opposite side of the mounting surface.
This mounting system
enables mounting to flat or round surfaces and allows for minimal 7
degrees of flexibility of
angle placement of the light. In this LED
emitter light bar model, an additional mounting option is provided.
The
adjustable, shock insulated mounts are attached to a simple,
inverted u-bracket type mount. The LED light bar
can then be
mounted via a single 3/8 bolt through the center of the bracket.
To
adjust, loosen bolts on either side just enough to adjust light head.
Tighten bolts once desired position is
achieved.
Larson Electronics, LLC
Phone: (877) 348-9680
Fax: (903) 498-3364
www.larsonelectronics.com
1
of
2
POWER
Connect power to power supply outputting low voltage between 9-42 volts DC.
This variable voltage allows greater versatility without affecting light output.
Ensure deutsch connectors are properly connected.
DETACHABLE CORDS
•
Cord is attached via a weatherproof 2-pin Deutsch connector.
•
The cord is detachable by depressing the tab on the top of the connectors. This enables the
operator to remove
and store the light while leaving the cord connected to the power source.
•
Additional or replacement cords can be ordered from our website. Contact us or visit LarsonElectronics.com for more
information.