background image

EPLC2-LB-45LED-RT-WLM

Larson Electronics, LLC

 

  Phone: (800) 369-6671 

 Fax: (903) 498-3364 

 www.larsonelectronics.com 

1

 of 

2

45W Hazardous Location Low Bay LED Fixture

Paint Spray Booth Approved - 6,300 lms - Wall Mount - T5

Instruction Manual

 

The Larson Electronics EPLC2-LB-45LED-RT-WLM Hazardous Location Low Bay LED Light Fixture provides operators 
with a powerful alternative to traditional hazardous location luminaries. Capable of replacing 250-watt metal halide lamps, 
this 45-watt low bay LED unit emits 6,300 lumens, carries an IP67 waterproof rating and features an extended lifespan of 
60,000+ hours. The factory sealed, hazardous location fixture is protected by a copper-free aluminum housing with an 
epoxy powder coated finish.

WARNING 

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE 

REFERENCE. CRITICAL SAFETY INSTRUCTIONS:  

INSTALLATION SHOULD ONLY BE CONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

RISK OF FIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES ELECTRICAL

SYSTEMS. IF NOT QUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE RATED LUMINAIRE FIXTURES VOLTAGE.

TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

 

READ  CAREFULLY  BEFORE  INSTALLING  THIS  FIXTURE.  SAVE  THESE  INSTRUCTIONS  FOR  FUTURE 

REFERENCE. THE 

EPLC2-LB-45LED-RT-WLM

  MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL 

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.  

WE  STRONGLY  ENCOURAGE  ONLY  A  LICENSED  ELECTRICIAN  INSTALL,  OPERATE  AND  MAINTAIN  THIS 

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET, 

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE. 

WARNING:

 

MAKE SURE POWER IS TURNED 

OFF

 BEFORE STARTING THE 

INSTALLATION OR PERFORMING ANY MAINTENANCE.

 

 

RISK OF FIRE/ELECTRIC SHOCK –

 

DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

 

RISK OF PERSONAL INJURY –

 

FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY. 

RISK OF BURN –

 

ALLOW FIXTURE TO COOL BEFORE SERVICING. 

WIRING 
Standard pigtail(flying leads) wiring 

We strongly encourage a licensed electrician install this product

, in all locations especially in outdoor areas 

where weatherproofing may be required. Universal voltage driver permits operation at 100V  -  277V AC, 50 or 60Hz 

except those factory ordered with low voltage 11V to 25V AC/DC. 

Warning: 

Check product label for correct input voltage!

 

Attach supply line wires to the appropriate light fixture wires as shown 

in the diagram 

 

Secure each pair of wires according to the diagram. Utilize a junction box or 

similar  device  and  take  precautionary  steps  for  weatherproofing  all 

connections if installed in a location where water may come in contact with the 

unit. Ensure the unit is properly grounded and that wiring is done according to 

all local and national electrical/building codes. 

Отзывы: