manualshive.com logo in svg

Lapple FIBRO FIBROTOR EM.NC Series, Руководство по сборке и эксплуатации

Поделиться
Скачать
Lapple FIBRO FIBROTOR EM.NC Series Скачать руководство пользователя страница 36

0   

 

7.5  ROTARY  TABLE - TURNING  ON AND OPERATION 

 

 

 

 

 

 

 

FIBROTOR

 

36

  | 

60

 

 

 

7.4.2

 

Path of motion 

Electric holding  brake is ventilated  (de-energised).   
During  the dividing procedure  by a servo  motor the  acceleration  and deceleration 
time must  be observed.  (NC controlled)   
If the NC rotary table has reached the target position, the worm shaft is stopped  by 
the  holding  brake.  

_________________________________________________________________ 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

     

  

 

 

 

 

 

 

 

 

 

 

 

 

       

     

      

 

 

 

   

 

        

 

    

   

 

 

_________________________________________________________________ 

Fig. 10 

Path of motion 

  Reference  point switch 

 

 

  Speed on  the table top 

  Brake 24V DC 

 

 

 

  n max 

   Proximity  switch 

 

 

 

  n min 

  Encoder reference  point signal 

 

 

7.5

 

Rotary table - turning on and operation 

The  rotary  table  is designed for mounting  in other  machines  or for assembly  with 
other  machines.  FIBRO  GmbH has  no control  over  the  intended  use of the rotary 
table. 
The  operator is responsible for  the safety  devices for operation of the  machine. 
Operation  without  safety  devices is prohibited. 

The  operator is responsible for  the safe operation and the  information  that  is 
necessary  for  the operation. 

 

Содержание FIBRO FIBROTOR EM.NC Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды