Lapple FIBRO FIBROTOR EM.NC Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 60

Lapple FIBRO FIBROTOR EM.NC Series Скачать руководство пользователя страница 31

5

ASSEMBLY

5.1 IMPORTANT SAFETY GUIDELINES

FIBROTOR

31

|

60

5

Assembly

5.1

Important safety guidelines

Incorrect installation

The  assembly  work should  be performed  by qualified personnel  only.  Work on the
power supply line connections should be performed by qualified electricians only. A
check must  be carried out  to ensure  that  the  power supply  frequency  and voltage
correspond  with the  data in the technical  specification. The  electric,  hydraulic  and
pneumatic  devices must  be connected  only  when  the  power supply  is turned  off.
Crushing  and electrocution  injuries.

When assembling the rotary table or its components, the following must be ensured:

•

the assembly site is suitable for the operational weight, including the
superstructural parts of the client and the tools.

•

the expected loads, torques and moments of inertia have been taken into
consideration.

•

the assembly site has been isolated with a signal strip.

•

the assembly site has been marked with danger signs.

•

only authorised persons have access to the work area and no other persons
could be endangered by the assembly work.

5.2

Installation requirements

The assembly site must be prepared for the assembly work and has to be clean and
even.
The mounting bolts must be available.

5.3

Assembly of the rotary table

5.3.1

Mechanical assembly

Rotary table damage. The rotary table should not be braced

while being bolted. The maximum bolting depth and the tightening moments of the
mounting bolts as well as the maximum offset for the cylindrical pins must be
observed.

«
...
29
30
31
32
33
...
»

Содержание FIBRO FIBROTOR EM.NC Series





























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды