manualshive.com logo in svg

Lantronix SM16TAT2SA, Инструкция по установке, Страница: 27 / 30

Поделиться
Скачать
Lantronix SM16TAT2SA Скачать руководство пользователя страница 27

Lantronix 

 

SMxTAT2SA Install Guide

 

33716 Rev. L 

                  

https://www.lantronix.com/

   

27   

Compliance Information 

FCC Regulations 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference 

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate 

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause 

harmful interference to radio communications. 
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will 

be required to correct the interference at the user's own expense. 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. 

Canadian Regulations 

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio 

interference regulations of the Canadian Department of Communications. 
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux 

appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le 

ministère des Communications du Canada.   

Declaration of Conformity (DoC) 

Declaration of Conformity 

Manufacture’s Name: Lantronix, Inc. 

Manufacture’s Address: 7535 Irvine Center Drive, Suite 100, Irvine, California 92618 
Declares that the product(s): SM8TAT2SA, SM16TAT2SA, SM24TAT2SA 
Conform(s) to the following Product Regulations: 
FCC Part 15 Class A, EN 55032:2012, EN 55024:2010 

Directive 2014/30/EU, Directive 2015/863/EU 

Low-Voltage Directive 2014/35/EU 

IEC62368-1/EN62368-1 

2011/65/EU EN 50581:2012 

Normas Oficiales Mexicans (NOM) 
With the technical construction on file at the above address, this product carries the CE Mark 
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and 

Standard(s). 
Place: Irvine, California   

 

Date: July 28, 2021

 

 

Signature: 

Fathi Hakam

 

Full Name: Fathi Hakam  

Position: Vice President of Engineering 

 

 

 

Содержание SM16TAT2SA































Отзывы:

Нет отзывов