manualshive.com logo in svg

Lantronix SISGM1040-284-LRT, Инструкция по установке, Страница: 41 / 45

Поделиться
Скачать
Lantronix SISGM1040-284-LRT Скачать руководство пользователя страница 41

Lantronix 

 

SISGM1040-284-LRT Install Guide

 

33808 Rev. E 

                   

https://www.lantronix.com/

   

41 

List Lantronix or third party equipment in the network (e.g., PCs, servers, switches, routers, or hubs, remote 

devices (camera, etc.), SFPs, etc.): ____________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

_________________________________________________________________________________________ 

 

Compliance Information 

CE/EN 55022 EN55024 

FCC part 15 approval Class A 

CE marking 

CISPR22/EN55032 Class A 

Radiated and Conducted Emissions

: ANSI C63.4:2014 with FCC Method 47 CFR Part 15, Subpart B, Class A Digital 

Device, CISPR PUB. 22 and Canada Standard ICES-003 Issue 6, Class A. 

European Standard EN 55032 Class A. Australian Standard AS/NZS CISPR 32 Class A. 

Harmonics

: European Standard EN 61000-3-2. Voltage Fluctuations: EN 61000-3-3.   

EMS

: European Standard EN 55024 (ESD: IEC 6100-4-2, RS: IEC 61000-4-3, EFT: IEC 61000-4-4, Surges: IEC 61000-

4-5, CS: IEC 61000-4-6, PFMF: IEC 61000-4-8, DIPs: IEC 61000-4-11. 

LVD

: IEC 60950-1:2005 (2

nd

 E Am 1:2009 +Am 2:2013; and/or EN 60950-12006+A11:2009+ 

A12:2013 

Safety

: LVD, UL Listed, IEC62368-1/EN62368-1 

Environmental

: NEMA TS-2-2016 (Power, Transients, Temperature Test) 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. 
 
 

 

 

Содержание SISGM1040-284-LRT














































Отзывы:

Нет отзывов