Lantronix SISGM1040-284-LRT Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 45

Lantronix SISGM1040-284-LRT Скачать руководство пользователя страница 24

Lantronix

SISGM1040-284-LRT Install Guide

33808 Rev. E

https://www.lantronix.com/

24

Alarm Relay (Digital Input and Digital Output Relay)

Connecting the DI/DO (Digital Input / Digital Output) Relay

1.

Insert the negative (ground)/positive DI/DO Relay wires into the

+

and

-

terminals,

respectively.

2.

To keep the DI/DO Relay wires from pulling loose, use a small flat-blade screwdriver to

tighten the wire-clamp screws on the front of the Terminal Block connector.

3.

Insert the Terminal Block connector prongs into the Terminal Block receptor.

Note

:

Digital output (relay): 24VDC/1A
Digital input: level 0 (Low) -> 0V to 6V, level 1 (High) -> 10V to 24V

FAULT

: The two contacts of the terminal block connector are used to detect user-configured events.

The two wires attached to the fault contacts form an open circuit when a user-configured event is triggered.

If a user-configured event does not occur, the fault circuit remains closed.

«
...
22
23
24
25
26
...
»

Содержание SISGM1040-284-LRT














































Отзывы:

Нет отзывов