background image

9: Administration

SGX  5150 IoT Device Gateway User Guide

134

TM

Quick Setup

Quick Setup provides a place to configure all basic settings in one place. You may access Quick 
Setup through the Administration menu or whenever you reset your system to factory defaults.

Note:

The SGX 5150 IoT Device Gateway Quick Start Guide provides for instructions on 

accessing Web Manager via SoftAP (go to 

www.lantronix.com/support/documentation

).

To Utilize Quick Setup

Using Web Manager

1. In the Web Manager, click the 

Administration

 tab.

2. Click 

Quick Setup

.

3. Click 

OK

 in the verification window which appears.

4. Update the Quick Setup information below:

Table 9-63  Bridge 1 (br0) Configuration

Table 9-64  Wi-Fi Protected Setup

Table 9-65  Current Configuration

Setting

Description

State

Select to enable or disable the state

Transparent Mode

Select to enable or disable the transparent mode.

Ethernet Interface

Select the desired interface:  eth0 or usb0

Bridging MAC Address

Enter the bridging MAC address

Bridging IP Address

Enter the bridging IP address

Bridging IPv6 Address

Enter the bridging IPv6 address

Auto Detect IPv4 
Address

Check the radio button to enable it. If checked, the SGX 5150 gateway will 
attempt to learn the IP Address by using the source or destination IP address of 
packets arriving on the Ethernet interface. 

Warning:

Running processes may be impacted while the SGX 5150 

gateway monitors Ethernet traffic to determine the wired host IP address.

Initial Scan Interval

Enter the 

Initial Scan Interval

 in seconds.

Scan Interval

Enter the 

Scan Interval

 in seconds.

Setting

Description

WPS (PBC)

Click this button for push button connect.

WPS (PIN)

Click this button for pin hole connect.

Setting

Description

Network Name (SSID)

View existing network name/SSID, if any.

State

Select to enable or disable the state

IPv4 State

Select to enable or disable the state

Содержание SGX 5150















































































































































Отзывы: