4: Open-QTM 410 Carrier Board
Open-Q 410 Dev Kit User Guide
28
NOTE:
The Open-Q
TM
410 Display Connector (J801) and mounting hole arrangement are physically compatible with
the Dragonboard 800 Display , and the Open-Q
TM
805 Display. Only display adapters labelled for use with the
Open-Q
TM
410 development kit should be connected.
Connecting the wrong display adapters may causes
permanent damage to the hardware.
Table 6 – Display Connector J801 Pinout
Pin No
Net
Description
1, 7, 13, 19,
25, 31, 39, 49,
59, 2, 12, 22,
30, 36, 42, 48,
54, 60
GND
Ground
3
BBCLK2
Clock output for HDMI Adapter board
33
VREG_L5_1P8
Power output from PM8916 VREG_L5 LDO. Default voltage is +1.8V.
35, 37
VREG_L17_2P85
Power output from PM8916 VREG_L17 LDO. Default voltage is +2.85V.
41
VREG_DBU4_5V
Power output from carrier board +5V buck regulator.
43
GP24_LCD_TE
APQ8016E GPIO24. Alternate function as vertical sync.
45
BLSP6_3
APQ8016E BLSP6 bit 3.
47
VREG_3P3
Power output from carrier board +3.3V LDO
51
GP32_DSI_SEL
APQ8016E GPIO32. Default use as display reset.
53
BLSP4_3_TS_RST
APQ8016E BLSP4 bit 3. Default use as touch screen reset.
55
BLSP4_2_TS_INT
APQ8016E BLSP4 bit 2. Default use as touch screen interrupt.
57
GP31_DSI_INT
APQ8016E GPIO31. Default use as display interrupt
4
GP118_MI2S_SCK
APQ8016E GPIO118. Alternate function as I2S.
6
GP25_LCD_RST_N
APQ8016E GPIO25. Default use as display reset.
10
MPP4_BL_CTRL
PM8916 MPP4. Default use as backlight control
14
GP119_MI2S_D0
APQ8016E GPIO119. Alternate function as I2S.
16
GP117_MI2S_WS
APQ8016E GPIO117. Alternate function as I2S.
18
BLSP4_1_I2C_SDA
APQ8016E BLSP4 bit 1. Default use as touch screen I2C.
20
BLSP4_0_I2C_SCL
APQ8016E BLSP4 bit 0. Default use as touch screen I2C.
24, 26
VPH_PWR_3P7
+3.7V power output
28
VREG_L6_1P8
Power output from PM8916 VREG_L6 LDO. Default voltage is +1.8V.
32, 34
DSI0_LANE2_FLT_N/P
MIPI DSI0 data lane2
40, 38
DSI0_LANE3_FLT_N/P
MIPI DSI0 data lane3
44, 46
DSI0_CLK_FLT_N/P
MIPI DSI0 clock
50, 52
DSI0_LANE0_FLT_N/P
MIPI DSI0 data lane0
56, 58
DSI0_LANE1_FLT_N/P
MIPI DSI0 data lane1
8, 5, 9, 11, 15,
17, 21, 23, 27,
29
NC
Not connected
4.7 USB Host / Device Connections
While the Open-Q
TM
410 Development Kit provides a USB micro-B (device, J601) connector and a dual USB
Type-A (host, J602) connector, the functionality of these connectors are mutually exclusive, with the USB
micro-B connector taking priority.
NOTE:
DIP switch (S501) must be left in the OFF position. The selection for USB device or host is determined by the
connectivity of the USB micro-B connector (J601) to an external USB host. If J601 is connected, the USB port
operates as device mode. If J601 is not connected, the USB port operates as host mode on J602.
It is recommended to power down before switching the USB device / host capability.
