manualshive.com logo in svg

Lantronix Maestro E205XT02, Руководство пользователя, Страница: 158 / 213

Поделиться
Скачать
Lantronix Maestro E205XT02 Скачать руководство пользователя страница 158

 

 

Services 

E220 Series Cellular Router User Guide 

 

158 

  PPTP  

Network > Interface > PPTP 

 
Point-to-Point Tunneling Protocol (PPTP) is the extension of Point-to-Point Protocol (PPP) for traditional 
dial-up network connection. It is the most common protocol that enables the corporates to implement 
Virtual Private Network (VPN) for extending their internal corporate network.  
 
PPTP client/user connects to their VPN server using computer, router or any networking device that 
supports PPTP. A TCP control connection is then established from client to the server in order to create 
a virtual tunnel. PPTP provides security by authenticating the users and packet filtering. PPTP controls 
the mapping and managing of VPN tunnel and the data inside the tunnel by encrypting and maintaining 
the connection. It stores the data within a PPP packet, which are then further stored inside IP Packets 
to be used for their destination. PPTP encrypts and compresses these  packets using PPP-based 
protocols such as PAP and CHAP. PPTP uses GRE (General Routing Encapsulation) to send/receive 
data. 
 

 

 

 

Parameters 

Description 

Interface Overview

 

Profile Name 

Displays the all the configured PPTP Interfaces. The pre-configured 
interfaces for the router are 

•

 

PPTP1 

 

Note 

•

 

Default Interfaces PPTP cannot be deleted. 

Status

 

Displays the following Interface details: 

•

 

RX  

•

 

TX   

Actions 

Select the action to be taken for the Interface. 

•

 

Connect  –

  Connects the interface or reconnects the 

already connected interface 

•

 

Stop –

 Stops the Interface 

•

 

Edit –

 Click to edit the Interface. 

•

 

Delete –

 Click to delete the Interface. 

 

 

Содержание Maestro E205XT02






















































































































































































































Отзывы:

Нет отзывов