Lantech IES-0008B Series страница 13 Скачать руководство пользователя

Страница: 13 / 17

Chapter 3 Hardware Installation

3.1Hardware installation

3.1.1Unpack switch and check the accessory with packing content list

3.1.2 Mount the switch on desired position. For the best ventilation, it is
suggested to mount the switch on metallic surface.

3.1.3 Connect the M12 connector of power input. The power supply for
IPES-0008B series is connected via a 5-pole M12 female connector while
IES-0008B is with a 5-pole M12 female connector as well.



Voltage of Power Input & PoE budget

Model name

Power input

PoE budget

IPES-0008B-41-12V

Dual 9~36VDC

60W for 12V input

(80W at dual input)

120W for 24V/36V

input

80W for 72V Input

(54V input is

recommended for

PTZ or heater

applications)

IPES-0008B-41-24V

Dual 9~56VDC

IPES-0008B-41-72V

Dual 50.4~90VDC

IES-0008B-41-12V

Dual 9.5~60VDC

IES-0008B-41-72V

Dual 50.4~90VDC

IPES-0005B-41-12V

Dual 9~36VDC

60W for 12V input

(80W at dual input)

120W for 24V/36V

input

80W for 72V Input

(54V input is

recommended for

IPES-0005B-41-24V

Dual 9~56VDC

IPES-0005B-41-72V

Dual 50.4~90VDC

Содержание IES-0008B Series


















Результаты поиска

Содержание IES-0008B Series

Отзывы:

Похожие инструкции для IES-0008B Series

Бренды по названию

Популярные бренды

Lantech IES-0008B Series, Руководство пользователя

Результаты поиска

Содержание IES-0008B Series

Отзывы:

Похожие инструкции для IES-0008B Series

Бренды по названию

Популярные бренды