INSTALLATION
PROCEDURE
FOR
LIGHT
POLE:
1.
Lift
the
light
pole
into
position
over
the
installed
anchors
(refer
to
FGP
area
light
anchor
kit
installation
guide)
as
shown
in
Fig.
1.
Ensure
that
the
base
plate
is
resting
on
all
four
washers.
2.
Install
washers
and
hexs nut
as
shown
in
Fig.
2.
3.
Plumb
and
level
the
pole
and
tighten
all
anchors.
4.
Connect
line
‐
in
wires
to
driver
plate
assembly.
Pass
wires
through
strain
relief.
See
Fig.
3.
Refer
to
wiring
diagrams
on
page
3.
5.
Ensure
that
the
wire
harness
connectors
are
pulled
through
the
top
of
the
driver
plate
assembly
through
the
front
cavity.
This
is
to
connect
the
luminaire
wiring.
6.
Gently
insert
the
driver
plate
assembly
into
the
top
of
the
pole.
Ensure
the
front
of
driver
plate
assembly
is
in
the
correct
orientation.
See
Fig.
3
and
4.
7.
Apply
downward
pressure
to
compress
the
gasket.
Tighten
the
six
hex
bolts
equally
using
a
13mm
wrench
until
snug.
Ensure
that
once
tightened,
the
driver
plate
assembly
rests
in
the
center
of
the
pole.
8.
Connect
luminaire
wiring
to
driver
plate
assembly,
see
Fig.
5.
9.
Gently
push
wires
down
inside
of
driver
plate
assembly.
Set
Luminaire
on
top
of
driver
plate
assembly,
ensuring
that
the
luminaire
mount
plate
is
seated
properly
on
the
top
of
the
driver
plate
assembly.
Use
an
8mm
hex
key
to
install
M10
x
55m
socket
head
cap
screw
and
sealing
washer
to
secure
luminaire
to
top
of
pole.
10. If
twist
lock
receptacle
is
specified,
remove
shorting
cap
and
install
photo
‐
eye
control
(not
included),
see
Fig.6.
11. Install
the
cover
plate
as
shown
in
Fig.
7
and
8.
Use
a
5mm
hex
key
to
tighten
internal
socket
head
cap
screws
to
secure
the
two
halves
together.
Tools
Required
•
Safety
glasses
•
Wrenches,
1
‐
1/4”
,
13mm
•
Screwdrivers,
Phillips
and
straight
blade
•
Wiring
tools
and
connectors
•
Proper
personnel,
crane
or
lift
for
hoisting
unit
onto
anchors
•
Level
•
Dimming
control,
if
required
•
Hex
keys,
8mm
with
10
‐
12”
extension,
5mm
•
Twist
lock
photo
eye
control,
if
required
Landscape
Forms
is
not
responsible
for
site
preparation
and
footings.
Refer
to
the
installation
guide
for
the
FGP
light
anchor
kit
for
installing
the
anchor
bolts.
CAUTION!
This
unit
is
heavy.
To
avoid
injury
or
damage
to
the
finish,
we
recommend
using
a
crane
or
lift
for
hoisting
the
unit
onto
the
anchors.
WARNING!
Pole
mounted
luminaires
must
be
attached
either
before
or
immediately
after
pole
installation. Failure
to
do
so
may
cause
vibration
damage
to
the
pole
and
will
void
the
pole
warranty.
ASSEMBLE
WITH
CARE!
Pangard II
Polyester
Powdercoat is
a
strong,
long
‐
lasting
finish.
To
protect
this
finish
during
assembly,
place
unwrapped
powdercoated parts
on
packaging
foam
or
other
non
‐
marring
surface.
Do
not
place
or
slide
powdercoated parts
on
concrete
or
other
hard
or
textured
surface
– this
will
damage
the
finish
causing
rust
to
occur.
Use
touch
‐
up
paint
on
any
gouges
in
the
finish
caused
by
assembly
tools.
Luminaire
2x
‐
Cover
plate
half
Twist
lock
receptacle,
optional
Installation Guide
FGP
Area Light
www.landscapeforms.com Ph: 800.521.2546
Date: October 5, 2018
Page 1 of 3
Included
components
Shorting
cap
for
Twist
lock,
optional
Pole
Driver
plate
assembly
1x
‐
M10
x
1.5
x
55mm
socket
head
cap
screw
with
sealing
washer
INSTALLATION
PROCEDURE FOR
OPTIONAL
PHOTO
EYE:
Refer
to
wiring
diagram
for
wiring
details.
1.
Remove
the
twist
lock
cap
from
the
top
of
the
light.
2.
Loosen
the
two
phillips head
screws
two
turns.
IMPORTANT!
Do
not
remove
the
screws.
Loosen
just
enough
to
rotate
the
receptacle.
3.
Rotate
the
receptacle
until
the
arrow
points
north.
Tighten
the
screws.
4.
Install
the
photo
eye
(not
supplied
with
unit)
rated
for
proper
line
voltage
(277v,
1.5A).
