Landoll Tilloll 875 Series Скачать руководство пользователя страница 33

Страница: 33 / 64

3-8 HYDRAULIC FOLD INSTALLATION - ALL FOLD MODELS

IMPORTANT

READ ALL SAFETY PRECAUTIONS AT THE

FRONT OF THE SECTION BEFORE ATTEMPT-

ING ANY OF THE FOLLOWING PROCEDURES.

3-8.1

Install wing fold bracket to wing hinge

using hinge pivot bolt through bracket, wing

hinge, second bracket, and hex lock nut. In-

stall base end of fold cylinders to main frame

cylinder anchor using cylinder pin and hair

pins. Install rod end of fold cylinders to wing

fold brackets inserting hinge pivot bolt

through wing fold bracket, flat washer, yoke,

roller, yoke, flat washer, wing fold bracket,

and hex lock nut. Do not overtighten bolts.

Linkage must be snug, but move freely

(See

Figures 3-2 and 3-4)

3-8.2

Install short and flat wing supports on

wings using u-bolts and 5/8-11 hex lock nuts.

Refer to

Figures 2-1 through 2-7, 3-2, and

3-4

for locations.

3-8.3

Install 90

elbows with restrictors into

base and rod end of each cylinder.

3-8.4

Install hoses per

Figures 3-9 and 3-10

and

Tables 3-3 and 3-4.

3-13

ITEM

PART NO.

HOSE LENGTH (MODEL USED)

1-397-010311102

102" (15F)

1-397-010311108

108" (15F)

1-397-010083

28" (15F)

1-397-010082

36" (15F)

1-397-0101058

56" (15F)

3-397-010040

21" (15F)

Table 3-3 Hydraulic Fold Hose Installation -

15’F Model

Содержание Tilloll 875 Series

































































Результаты поиска

Содержание Tilloll 875 Series

Отзывы:

Похожие инструкции для Tilloll 875 Series

Бренды по названию

Популярные бренды

Landoll Tilloll 875 Series, Руководство оператора

Результаты поиска

Содержание Tilloll 875 Series

Отзывы:

Похожие инструкции для Tilloll 875 Series

Бренды по названию

Популярные бренды