Landoll BRILLION TURFMAKER II SL, Руководство оператора

Страница: 74 / 100

3-16 9K998
OPERATION
Acre Meter - Optional
Settings for Loup Acre Meters
After 05/15/2012
The battery operated acre counter operates in one of two
modes. In sleep mode, the display is blank, and the
counter is accumulating acres. Sleep mode will be
entered if a button is not pressed for 20 seconds. In entry
mode, the display is on, and the operator can enter
values. To get into entry mode, press the
*
/FUNC
button. If you continue to press the
*
/FUNC button, the
acre counter will cycle through the functions that it can
perform. The LEDs above the display indicate which
function is selected.
The available functions are:
Field Acres, Total Acres, Pulses per 400 ft, Width,
Password and Low Battery
Field Acres
Press the
*
/FUNC button until the “ FIELD ” LED is lit.
The digits indicate the acres covered since the field acre
counter was cleared.
To clear the field acre count, press the
UP and DOWN
buttons simultaneously for two seconds. If a password
has been entered, you will not be able to clear the total
acre count. Field acres will count in tenths of an acre up
to 9999.9 acres.
Total Acres
Press the
*
/FUNC button until the “ FIELD ” and “ TOTAL ”
LEDs are lit. The digits indicate the acres covered since
the total acre counter was cleared.
To clear the total acre count, press and hold the
UP and
DOWN buttons for two seconds. If a password has been
entered, you will not be able to clear the total acre count.
Total acres will count from.1 to 99999 acres.
Pulses Per 400 Feet
Press the
*
/FUNC button until the “ PULSES ” LED is lit.
The number in the display indicates how many pulses are
generated for every 400 feet driven. There are two
methods to enter the pulses per 400 feet:
1. If you know the number, select it using the
UP and
DOWN buttons. When you press the
*
/FUNC
button, the Acre Counter will accept the number in
the display as the new pulses per 400 feet.
See
Table 3-1 .
2. If you do not know the pulses per 400 feet, press and
hold the UP and DOWN buttons until the “0000”
appears in the display. The “ PULSES ” LED will blink.
The acre counter is now counting shaft rotations.
Enter the cab and drive 400 feet. Press the
*
/FUNC
button to wake up the acre counter. The “ PULSES ”
LED will light. The number displayed is the pulses
per 400 feet. Press the
*
/FUNC button to accept the
setting.
If a password is set, you will not be able to adjust the
pulses.
Width
Press the
*
/FUNC button until the “ WIDTH ” LED is lit.
The number displayed is the length of your implement in
feet.
To adjust the width, press the
UP and DOWN buttons. If
a password has been entered, you will not be able to
adjust the width.
The length can be adjusted from .1 to 99.9 feet, in tenths
of a foot.
Password
The password function allows you to protect the total
acre count, pulses per 400 feet, and width settings with a
password. This stops anyone from accidentally changing
those settings. When the acre counter is shipped, the
password is disabled. You can modify the pulses per 400
feet and implement width at any time.
Press the
*
/FUNC button until the “ PASS ” LED is lit. The
digits will display the word “ Ent ” or “ dIS ”.
If the display shows “dIS”: The password is disabled.
The total acre count, pulses/400 feet, width, and
password settings can be adjusted using the
UP and
DOWN buttons. The password can also be changed
using the UP and DOWN buttons.
If the display shows “Ent”: You must enter your
password using the UP and DOWN buttons. When your
password is displayed, press the
*
/FUNC button to test
the password. If the password is correct, you will be able
to change the acre counter settings. The password will
be viewable until the acre counter powers down. When
the acre counter is powered up again, you will have to
re-enter the password to change settings.
If the password is not correct, you will not be able to
change the acre counter settings. When the “
PASS ”
function is selected again, “ Ent ” will appear in the
display.