Landoll 855 HD Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 68

Landoll 855 HD Series Скачать руководство пользователя страница 35

MAINTENANCE AND LUBRICATION

4-7

Gooseneck, Frame, And Deck

Repairing Structural Defects

If any structural defect is found, the fault must be
corrected before further use of the vehicle. To continue
usage could endanger the trailer, its load, personnel,
traffic, and properties. If any cracks or breaks are found,
contact the Landoll factory for repairs. Inspect the deck
daily for broken or missing planks or missing
attachments. Replace any defective parts promptly.

Hydraulic System

General

1.

Check the oil level of the tractor wet kit weekly, or
after any leakage.

See Table 4-1

for proper hydraulic

oil. Check the hydraulic oil level with hydraulic
cylinders in the retracted position and the hydraulic
pump disengaged. Enough volume in tank
(approximately 15 gallons) above hydraulic oil level
must be available to accept extra oil from cylinders
when retracted.

2.

Overfilling can cause hydraulic fluid overflow during
operation.

3.

Hydraulic system pressure relief valves should be set
at 2500 psi.

4.

Check hoses weekly for cracks or leaks. If a valve or
line leaks, it should be replaced immediately.

«
...
33
34
35
36
37
...
»

Содержание 855 HD Series





































































Отзывы:

Нет отзывов