3-6
F-1130-2304
Center Frame and Lift Assembly
2411AFG-07-09
IMPORTANT
Read all safety precautions at the front of the section
before attempting any of the following procedures.
WARNING
1.
Place frame assembly on stands approximately 36”
high. The assembly area should be a large level area
of sufficient size to accommodate the Weatherproofer
when fully assembled
RT and LT is
determined from standing at the back looking forward.
NOTE
The front and rear tower plate assemblies, wing stop
mount assembly, and spring/clamp shank assemblies
are installed at the factory.
2.
Remove any shank assemblies that have been turned
around or mounted inside the frame for shipping, and
reposition,
through
for shank placement.
NOTE
All lifts and hubs/spindle come already assembled
from the factory.
3.
Install a UHMW bearing between all 4 inner bearing
locators around the center lift assembly.
4.
Insert a UHMW bearing into each bearing cap and
install the cap and bearing over the end of center lift
assembly.
5.
Raise the center lift assembly into the center frame
and attach each end bearing cap to the center frame
with 3/4 x 2-1/2 bolts and 3/4 lock nuts
6.
Install all 4 inner lift bearing mounts with 3/4 x 2 bolts
and 3/4 lock nuts.
NOTE
Make sure the center lift will rotate freely in the center
frame after it is assembled.
NOTE
Be sure the 4, 1-5/8 x 1-1/4 x 1 bushings are installed
in the lift plate mounts and center lift assembly mount
plates
7.
Install a 1-1/4 x 1 spacer in rod and base end cylinder
clevis. Attach both ends of the cylinder with 1-1/4 x 7
pins, 1-1/4 washers and 5/16 x 2-1/2 spring pins as
shown
8.
Attach the depth control plates to back of depth with
1/2 x 2 bolts and 1/2 lock nuts. Install a 1 x .640 x 5/8
bushing in the depth stop assembly plate align hole of
plate with front top hole of depth control plates, install
a 1 x .640 x 5/8 bushing between top rear of plates
secure with 5/8 x 2 bolts and 5/8 lock nuts.
9.
Attach the front of the depth stop assembly to front of
center frame assembly bracket with slide plate
between bracket and depth stop tube assembly,
depth stop guide on top, limit valve on bottom of
bracket with plunger to rear of machine, secure with
5/16 x 5-1/2 bolts and 5/16 lock nuts.
10. Install the tire/wheel assemblies to all hub/spindle
assemblies using 3/4 flange wheel nuts.
11. Attach the RT/LT light bracket assemblies with yellow
reflectors to front of machine with 1/2 x 4-1/2 bolts, 1/2
washers and 1/2 lock nuts. Install the transport locks
in the storage locations on top of light bracket
assemblies with L-pins and hairpin clips.
Do not attempt to lift heavy parts (such as the
frame, disc gangs, wheel lift, and pull hitch)
manually. Use a hoist or a forklift to move these
parts into position.
Содержание 2411
