Landoll 2211 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 74

background image

ASSEMBLY INSTRUCTIONS

3-13

Depth Stop Tube Assembly

1.

Attach the depth stop mount plate to the lift using
3/8-16 x 1-1/4 hex head cap screws and hex lock
nuts.

2.

Lay the depth stop tube assembly on top of the
center frame. Insert a 5/8-11 x 3 hex head cap screw
in the front hole (2211-09 & -11 models) or rear hole
(2211-13 & -15 models) of the tube assembly from
the left side

(See Figure 3-7.)

Install a 5/8-11 hex nut

on the screw. Do not over tighten, as the depth stop
must pivot on this screw. Insert the screw through the
depth stop mounting plate on the center lift and
secure with a 5/8-11 hex lock nut.

3.

Insert 90

o

elbow fitting in the back of the limit valve

and straight adapter (2211-09 & -11 models) or 90

o

adapter (2211-13 & -15 models) in the side nearest
the center of the machine.

4.

Using 5/16-18 x 4 hex head cap screws secure the
front end of the depth stop tube assembly to the top
of the frame mount with the spacers, depth stop
plate, and 5/16-18 hex lock nuts. Attach the limit
valve to the bottom side of the center frame mount
using these same screws.

IMPORTANT

It may be necessary to leave these screws loose to
attach the valve hoses later.

«
...
27
28
29
30
31
...
»

Содержание 2211











































































Отзывы:

Нет отзывов

Похожие инструкции для 2211

Бренд: ZOLL Страницы: 84

Бренд: Kaivac Страницы: 29

Бренд: MacDon Страницы: 65

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

KOMPAN SPF28666S

Бренд: Bommelland Страницы: 23

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: FEAS Страницы: 72

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды