ASSEMBLING YOUR L&L EASY-FIRE KILN
easy-fire-install.pdf
3/1/2007 Rev 1.3
Page 1
2007
L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com
ASSEMBLING YOUR L&L EASY-FIRE KILN
TABLE OF CONTENTS
TOOLS NEED FOR THE JOB . . . . . . . . . . . 1
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Inspect for visible damage . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Remove Top from Carton . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpack Instructions, Vent and Furniture Kit . . . . . . . . . . . . 2
Unpacking the kiln . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ASSEMBLING THE STAND . . . . . . . . . . . . . 4
REMOVING THE LID . . . . . . . . . . . . . . . . . . 5
REMOVING THE HINGE . . . . . . . . . . . . . . . 6
REMOVING THE CONTROL PANEL AND
ELEMENT COVER AS ONE ASSEMBLY . 6
REMOVING THE CONTROL PANEL . . . . 8
REMOVING ELEMENT COVER BOX . . . 9
LOCATING THE KILN . . . . . . . . . . . . . . . . . 10
SETTING UP THE KILN . . . . . . . . . . . . . . . . 10
SETTING UP THE HINGE . . . . . . . . . . . . . . 12
REASSEMBLING THE CONTROL PANEL 15
If you removed the panel separate from
the element cover box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
REATTACHING CONTROL BOX . . . . . . . . 16
TOOLS NEED FOR THE JOB
You will need the following tools for the job:
1) Philip’s head screw driver (medium size head)
2) Knife
3) Needle Nose pliers
4) Adjustable Wrench
5) Level
6) Safety Goggles
7) Special Spring Hinge Tool (provided)
WHAT SHOULD YOU READ?
The information in these installation instruc-
tions is as complete as we can make it - which
means that there is more than most people will
need to read or think about . Each heading is self-
contained (for instance “Assembling the Stand”)
Most people will be able to figure out how to
assemble their stand by looking at it - so only
read this heading if you get stuck .
First of all be comfortable with where you
are putting your new kiln . If you have any
questions about that read the information about
clearances, ventilation, etc . in the “Installation”
tabbed section . Do that first so you don’t have
to redo your work .
If there is anything we feel you must read we
will call it to your attention with one of these
shaded boxes .
CAN YOU MOVE THE KILN
WITHOUT DISASSEMBLING IT?
The kiln is shipped mostly assembled (except
for the stand and the disengaged hinge spring) .
It is possible to move the kiln without disassem-
bling it . However, these kilns, particularly the
e28S and e28T, are very heavy and awkward to
move . If you decide to move it without disas-
sembling the sections first be absolutely certain
you have at least two or three strong people
who are familiar with proper lifting techniques .
Serious back injury could result if such a heavy
object is lifted improperly . See page 5 for details
on how to do it - there are specific instructions
depending on which model you have .
