Land Pride SGC0554 Скачать руководство пользователя страница 19

Section 3: Operating Procedures

Table of Contents

SGC0554 Claw Grapple 380-275M

11/6/18

15

Release A Load

1.

Be sure to read and understand all safety alerts 
under 

“Operating Safety” 

on page 12.

2. Stop in front of desired location.

3. Slowly raise load to required height.

4. Move forward slowly checking to make sure grapple 

and load clears all obstacles. 

5. Stop forward movement when load is positioned over 

its release location.

6. Releasing load requires a combination of tilting front 

of grapple down, raising upper jaw, and raising 
loader arms. The order in which the load is released 
will vary depending on type of material being 
released. The most important objective is to have the 
load under control throughout the release.

7.

Once load has settled onto the pile, slowly back up 
making sure grapple clears all objects and there are 
not any pedestrians or other traffic behind or on 
either side.

8. Leave enough clearance when turning and/or 

lowering the grapple that it does not make contact 
with obstacles such as buildings, trees, fences etc. 

9. Lower grapple to transporting height (low to the 

ground) before moving again.

Rip Out Bushes

1.

Be sure to read and understand all safety alerts 
under 

“Operating Safety” 

on page 12.

2. Open upper claw halfway. 

3. Rotate front of grapple down while lowering unit until 

upper teeth extend into the ground on the far side of 
the bush and lower teeth are on the near side.

4. Close grapple claws around the roots of the bush.

5. Raise grapple up to rip bush from ground.

Break Sod With Lower Jaw

1.

Be sure to read and understand all safety alerts 
under 

“Operating Safety” 

on page 12.

2. Open upper jaw halfway. 

IMPORTANT

Do not operate attachment with lower 

teeth extending very deep into the ground. Doing so 
can damage equipment.

IMPORTANT: 

Check for stumps, rocks, and other 

solid objects in the ground before breaking sod. Flag 
solid objects to protect against hitting them while 
breaking sod. 

IMPORTANT: 

Do not make turns with lower jaw in 

the ground to break sod. Turning while breaking sod 
can damage the grapple and loader arms.

3. Lower grapple until bottom teeth start to go into the 

ground. Do not go very deep into the ground. Always 
keep loader arms out of the ground.

4. Drive straight forward to break up sod and push 

debris ahead of attachment.

Back Raking With Upper Jaw

1.

Be sure to read and understand all safety alerts 
under 

“Operating Safety” 

on page 12.

2. Open upper jaw fully and rotate front of grapple down 

while lowering unit until the tips of the upper teeth 
touch the ground.

3. Back-up to rake loose sticks and debris into a pile.

4. For instructions on how to pick-up the raked pile, see 

“Pick-Up A Load” 

on page 14.

General Operating Instructions

By now you should have familiarized yourself with the 
Operator’s Manual for your Claw Grapple. If you haven’t, 
please do so now. Proceed by getting onto the seat of 
your tractor and starting it up. It isn’t going to take you 
long to learn how to use your new Land Pride Claw 
Grapple, but we do recommend that you take a little time 
to practice securely attaching and detaching your grapple 
to and from your mounting plate. It is also important to 
practice lifting, lowering, maneuvering, and placing a load 
until you gain the confidence and skill needed to have a 
good feel in what you are doing. We cannot overstress 
the importance of following the safety information and 
operating procedures that are spelled out in this 
Operator’s Manual. 

As you quickly become more skilled and adept in using 
your Claw Grapple, you will soon learn that it is always 
more important to focus on the “don’ts” than it is to focus 
on the “dos”. For example, don’t exceed the lift capacity of 
your grapple or tractor. Don’t lift your load too high 
creating an unstable load and unsafe situation. Don’t tilt 
your load too far backwards, setting up a situation that 
could cause your load to roll or spill backwards onto you, 
the tractor, and the operator’s platform. Don’t drive too 
fast for your ground and load conditions. Don’t work on or 
around slippery or sloped areas that could cause you to 
lose control of the tractor. Don’t allow pedestrians, pets, 
or livestock to approach the danger zone of your working 
area. Always close grapple upper claw and lower grapple 
until it is resting on the ground before leaving your tractor. 

If you just follow these few safety reminders, you will find 
that you will quickly become very adept, handy, and 
skillful at using your Land Pride Claw Grapple.

See

 “Specifications & Capacities” 

on page 21 and 

“Features & Benefits”

 on page 21 of your Operator’s 

Manual for additional information. 

IMPORTANT

Check full range of motion before 

rotating attachment down to back rake. See 

“Check 

Equipment Clearances” 

on page 10.

Содержание SGC0554



























Отзывы: