Land Pride SB10 Series Скачать руководство пользователя страница 36

Страница: 36 / 42

Section 6: Maintenance & Lubrication

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M

2/11/21

Table of Contents

Gearbox

Remove oil level plug shown with arrow. If oil is below

bottom of plug hole, add recommended gear lube

through oil level plug hole until oil flows out of the hole.

Reinstall and tighten oil level plug.
Type of Lubrication: 80-90W EP Gear Lube
Quantity = Fill until oil begins to flow out of oil level plug

hole in gearbox.

NOTE:

Do not overfill! Snow Blower should be level

when checking oil. Oil expands when hot, therefore,

always check oil level when cold.

33293

SB1051 & SB1064 Gearbox

SB1574 & SB2584 Gearbox

Do Not

Overfill

Do Not

Overfill

33294

NOTE:

Use a suction or siphon pump to drain

gearboxes of oil when there is not an oil drain plug.

33302

23759

Driveline U

joints

Driveline U

joint with grease every 8 hours of operation

2 - Zerks
Type of grease = Multi-Purpose
Quantity = Coat Generously

Driveline Shaft

Disconnect driveline shaft from the tractor and slide

apart. Clean and coat the inner tube of the driveline shaft

with a light film of grease and then reassemble.
Type of grease = Multi-Purpose
Quantity = Coat Generously

Hours

Required

Содержание SB10 Series











































Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды

Land Pride SB10 Series, Руководство оператора

Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды