Land Pride SB10 Series Скачать руководство пользователя страница 10

Страница: 10 / 42

Section 1: Standard Assembly & Set-up

SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M

2/11/21

Table of Contents

Section 1: Standard Assembly & Set-up

Tractor Requirements

Tractor horsepower and hitch category should be within

the range noted below. Tractors outside the horsepower

range must not be used.

Tractor Horsepower Rating

SB10 Series . . . . . . . . . . . . . . . . . . . . .18 to 32 HP

SB15 Series . . . . . . . . . . . . . . . . . . . . . . .30-59 HP

SB25 Series . . . . . . . . . . . . . . . . . . . . . .43-105 HP

Hitch Type:

SB10 Series . . . . . . . . . . . . . . . . . . . .3-Point Cat. I

SB15 Series . . . . . . . . . . . . . . . . . . . .3-Point Cat. I

SB25 Series . . . . . . . . . . . . . . . . .3-Point Cat. I & ll

PTO Speed . . . . . . . . . . . . . . . . . . . . . . . . .540 RPM

Hydraulic Quick Disconnect Outlets (Optional)

Chute Rotational Adjustment. . . . . . . Duplex Outlet

Chute Tilt Adjustment . . . . . . . . . . . . Duplex Outlet

Tractor Weight . . . . . . . . . . . . . . .See Warning Below

WARNING

Ballast weights may be required to maintain steering control.

Refer to your tractor’s operator’s manual to determine proper

ballast requirements.

Torque Requirements

Refer to

“Torque Values Chart”

on page 38 to

determine correct torque values for common bolts. See

“Additional Torque Values”

at bottom of chart for

exceptions to standard torque values.

Dealer Set-up Instructions

When included, it is simpler to assemble the optional

outer skid shoes or outer wear bars before removing the

shipping crate. See

“Skid Shoes, Outer”

“Wear Bars,

Outer”

on page 13 for detailed installation instructions.

Loading & Unloading

Refer to Figure 1-1:

There are two lifting holes (one on each end panel).

These lift holes are provided for attaching a lift chain to

the Snow Blower during loading and unloading.

Lift Points

Figure 1-1

33248

Chute Assembly

Refer to Figure 1-2:

1. Remove bearing strap (#2A) from Snow Blower

housing. Keep cap screws (#3), bearing strap (#2A),

chute bearings (#7), lock washers (#5), and hex

nuts (#4) for reattachment of discharge chute (#1).

2. Position discharge chute (#1) so that it is facing

straight back as shown.

3. Keep chute facing straight back. Slide base of

discharge chute (#1) over UHMW chute bearing

ring (#6) until base of chute is fully under the other

two remaining bearing straps (#2B & 2C).

4. Reattach bearing strap (#2A) to Snow Blower

housing by inserting existing 3/8"-16 x 1 1/2" cap

screws (#3) through bearing strap (#2A), chute

bearings (#7), and Snow Blower housing flange.

5. Secure bearing strap with existing lock washers (#5)

and hex nuts (#4). Tighten nuts to the correct torque.

Chute Assembly

Figure 1-2

33255

Содержание SB10 Series











































Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды

Land Pride SB10 Series, Руководство оператора

Результаты поиска

Содержание SB10 Series

Отзывы:

Похожие инструкции для SB10 Series

Бренды по названию

Популярные бренды