manualshive.com logo in svg

Land Pride RCR2660, Руководство оператора, Страница: 31 / 40

Поделиться
Скачать
Land Pride RCR2660 Скачать руководство пользователя страница 31

Section 5: Maintenance & Lubrication 

Table of Contents

12/4/18

RCR2660 and RCR2672

 Rotary Cutters 

312-783M

27

Skid Shoe Maintenance

Refer to Figure 5-6:

WARNING

!

To avoid serious injury or death:  
Excessive wear on skid shoes can damage side panels, cause 

inadequate operation of cutter, and create a safety hazard. 

Always replace skid shoes at the first sign of wearing thin.

There are two skid shoes mounted on the cutter sides. 
Check both skid shoes for wear and replace if necessary. 
Order only genuine Land Pride parts from your local Land 
Pride dealer.

Skid Shoe Replacement

Figure 5-6

1.

Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2), 
and skid shoe (#1) as shown. 

2. Plow bolts should be checked for wear and replaced 

if necessary.

3. Attach new skid shoe (#1) to cutter with existing 

3/8" plow bolts (#2) and secure with 3/8" hex whiz 
nuts. Torque to 31 ft. lbs.

4. Repeat on opposite side.

Long Term Storage

Clean, inspect, service, and make necessary repairs to 
the implement when storing it for long periods and at the 
end of the season. This will help ensure the unit is ready 
for field use the next time you hook-up to it.

DANGER

!

To avoid serious injury or death:  

•

Always disconnect driveline from power take-off shaft 

before servicing drivetrain and cutter blades. The power 

take-off can be engaged if tractor is started.

22454

Land Pride Skid Shoe Replacement Parts

Part No.

Part Description

312-602D

SKID SHOE

802-603C

PLOW 3/8" - 16 x 1" GR5

803-198C

NUT HEX WHIZ 3/8-16 PLT

•

Always secure equipment with solid, non-concrete supports 

before working under it. Never go under equipment 

supported by concrete blocks or hydraulics. Concrete can 

break, hydraulic lines can burst, and/or hydraulic controls 

can be actuated even when power to hydraulics is off.

1.

Clean off any dirt and grease that may have 
accumulated on the cutter and moving parts. Scrape 
off compacted dirt from the bottom of deck and then 
wash surface thoroughly with a garden hose. A 
coating of oil may also be applied to the lower deck 
area to minimize oxidation.

2. Check blades and blade bolts for wear and replace if 

necessary. See 

“Cutter Blade Maintenance” 

on 

page 24.

3. Inspect for loose, damaged, or worn parts and adjust 

or replace as needed.

Repaint parts where paint is worn or scratched to prevent 
rust. Ask your Land Pride dealer for aerosol touch-up 
paint. Paint is also available in touch-up bottles with 
brush, quarts, and gallon sizes by adding TU, QT, or GL 
to the end of the aerosol part number.

4. Replace all damaged or missing decals.

5. Lubricate as noted under 

“Lubrication” 

on page 28.

6. Store cutter on a level surface in a clean, dry place. 

Inside storage will reduce maintenance and make for 
a longer cutter life.

7.

Follow all unhooking instructions on page 20 when 
disconnecting tractor from cutter.

Ordering Replacement Parts

Land Pride offers equipment in factory standard beige 
color with black highlights. Equipment in special colors 
may be purchased in Green, Red, or Orange. Because of 
the variety of colors available, special attention must be 
given to the part number to prevent ordering the wrong 
replacement part. A suffix number corresponding to one 
of the colors below must be added at the end of Land 
Pride’s part number when ordering a replacement part 
with that color. Parts ordered without a suffix number will 
be supplied in factory standard colors.

For example, if you are ordering a replacement part with 
part number 555-555C and the existing part is red, then 
add the suffix 83 to the end of the number to make the 
part number read 555-555C83.

Land Pride Touch-up Paint

Part No.

Part Description

821-011C

PAINT LP BEIGE SPRAY CAN

821-066C

PAINT ORANGE SPRAY CAN

821-070C

PAINT GP GLOSS BLACK SPRAY CAN

82  . . . . . .  Orange

85  . . . . . . . Black

Содержание RCR2660









































Отзывы:

Нет отзывов