Land Pride RCR2660 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

Land Pride RCR2660 Скачать руководство пользователя страница 3

Table of Contents

©

Copyright 2018 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

12/4/18

RCR2660 and RCR2672

Rotary Cutters

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol  . . . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 7
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 1: Assembly & Set-up . . . . . . . . . . . . 8

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Hitch Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Gearbox Vented Dipstick   . . . . . . . . . . . . . . . . . . . . 9
Driveline Installation   . . . . . . . . . . . . . . . . . . . . . . . . 9
3-Point Hookup  . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Hook-up Driveline to Tractor Power Take-Off   . . 11
Check Clearances  . . . . . . . . . . . . . . . . . . . . . . . 11
Check Driveline Collapsible Length  . . . . . . . . . . 11
Shorten Driveline  . . . . . . . . . . . . . . . . . . . . . . . . 11
Check Driveline Interference   . . . . . . . . . . . . . . . 12
Single Tail Wheel Assembly . . . . . . . . . . . . . . . . 12

Check Chain Option . . . . . . . . . . . . . . . . . . . . . . . 13
Front and Rear Safety Guard Options . . . . . . . . . . 13

Front Safety Guard . . . . . . . . . . . . . . . . . . . . . . 13
Rear Chain Guard . . . . . . . . . . . . . . . . . . . . . . . 13

Section 2: Adjustments . . . . . . . . . . . . . . . . . 14

Deck Leveling & Height Adjustments . . . . . . . . . . 14

Deck Leveling From Left to Right  . . . . . . . . . . . . 14
Deck Leveling From Front to Rear  . . . . . . . . . . . 14
Tractor Center 3-Point Adjustment . . . . . . . . . . . 15
Tail Wheel Height Adjustment   . . . . . . . . . . . . . . 16

Section 3: Operating Instructions . . . . . . . . . 17

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 17
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tractor & Cutter Inspection  . . . . . . . . . . . . . . . . . . 18
Transporting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Blade Engagement & Disengagement   . . . . . . . . . 19

Blade Engagement . . . . . . . . . . . . . . . . . . . . . . 19
Blade Disengagement . . . . . . . . . . . . . . . . . . . . 19

Field Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Unhooking the Rotary Cutter . . . . . . . . . . . . . . . . . 20
General Operating Instructions . . . . . . . . . . . . . . . 21

Section 4: Options . . . . . . . . . . . . . . . . . . . . . 22

Front and Rear Safety Guard Options . . . . . . . . . . 22

Front Rubber Guard  . . . . . . . . . . . . . . . . . . . . . . 22
Front Chain Guard  . . . . . . . . . . . . . . . . . . . . . . . 22
Rear Chain Guard   . . . . . . . . . . . . . . . . . . . . . . . 22

Chain Check Option . . . . . . . . . . . . . . . . . . . . . . . 23

Section 5: Maintenance & Lubrication . . . . . 24

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 24
Driveline Protection  . . . . . . . . . . . . . . . . . . . . . . . . 25
Clutch Run-In   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Clutch Assembly and Disassembly  . . . . . . . . . . . . 26
Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . . 27
Long Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 27
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 27
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Driveline Inner Tube  . . . . . . . . . . . . . . . . . . . . . . 28
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 28
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 28
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Tailwheel Spindle Tube   . . . . . . . . . . . . . . . . . . . 29
Tailwheel Hub   . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Section 6: Specifications & Capacities  . . . . . 30
Section 7: Features & Benefits   . . . . . . . . . . . 32
Section 8: Troubleshooting  . . . . . . . . . . . . . . 33
Section 9: Torque Values Chart  . . . . . . . . . . . 34
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 35

«
1
2
3
4
5
...
»

Содержание RCR2660









































Отзывы:

Нет отзывов