Land Pride RCR2660 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 40

Land Pride RCR2660 Скачать руководство пользователя страница 26

Section 4: Options

Table of Contents

12/4/18

RCR2660 and RCR2672 Rotary Cutters 312-783M

22

Front Rubber Skirt Safety Guard

Figure 4-1

Front Chain Safety Guard

Figure 4-2

Rear Chain Safety Guard

Figure 4-3

20957

20956

20958

Section 4: Options

Front and Rear Safety Guard Options

DANGER

!

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Double row chain guards should

be used when cutting along roadways and in areas where

people may be present. Stop blade rotation if bystanders are in

or around the area.

WARNING

!

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Land Pride offers two types of front guards to best suit
your application. They are the rubber skirt guard and
chain skirt guard. The rubber skirt guard is more
economical and designed for light duty applications. The
chain guard is designed to handle heavier applications
where cutter blades make contact with solid dense
objects that are capable of tearing through rubber skirts.

Front Rubber Guard

Refer to Figure 4-1:

Part Number & Description

312-782A RCR2660 Front Rubber Skirt Safety Guard

312-794A RCR2672 Front Rubber Skirt Safety Guard

See

“Front Safety Guard”

on page 13 for proper

installation.

Front Chain Guard

Refer to Figure 4-2:

Part Number & Description

312-781A RCR2660 Front Chain Safety Guard

312-793A RCR2672 Front Chain Safety Guard

See

“Front Safety Guard”

on page 13 for proper

installation.

Land Pride offers a rear chain safety guard designed to
handle heavy applications where cutter blades make
contact with solid dense objects.

Rear Chain Guard

Refer to Figure 4-3:

Part Number & Description

312-410A RCR2660 Rear Chain Safety Guard

312-396A RCR2672 Rear Chain Safety Guard

See

“Rear Chain Guard”

on page 13 for proper

installation.

«
...
24
25
26
27
28
...
»

Содержание RCR2660









































Отзывы:

Нет отзывов