Land Pride RCR2660 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 40

Land Pride RCR2660 Скачать руководство пользователя страница 29

Section 5: Maintenance & Lubrication

Table of Contents

12/4/18

RCR2660 and RCR2672

Rotary Cutters

25

Counterclockwise Blade Rotation

Figure 5-1

Cutter Blade Assembly

Figure 5-2

Refer to Figure 5-2:

10. Insert blade bolt (#1) through blade (#2), dish

pan (#3), and flat washer (#4). Secure blade with a

new locknut (#5)

and torque to 450 ft-lbs.

11. Repeat step 10 for the other blade.

20950

Blade Bolt
Access Cover

24590

Use 1-11/16"

Socket Wrench

On Blade Nut (#5)

Land Pride Cutter Blade Parts

Item Part No.

Part Description

318-586A

BLADE BOLT KIT
(Includes items 1, 4, & 5 below)

1

802-277C

BLADE BOLT 1 1/8-12 x 3 7/16 WITH KEY

2

820-137C

RCR2660 BLADE 1/2 x 4 x 25 CCW

2

820-168C

RCR2672 BLADE 1/2 x 4 x 29 CCW

3

312-820H

RCR2660 15 DISHPAN WELDMENT

3

312-811H

RCR2672 19 DISHPAN WELDMENT

4

804-147C

WASHER FLAT 1 HARD ASTMF436

5

803-170C

NUT HEX TOP LOCK 1 1/8-12 PLATE

IMPORTANT:

Examine blade bolts, washers, and

bushings for excessive wear and replace if worn.

IMPORTANT:

A locknut that has been removed can

lose its thread locking properties. Reusing a used
locknut can result in a thrown blade. Always use a
new locknut when installing blades.

12. Replace blade bolt access cover shown in

Figure 5-1:

13. If replacing dishpan (#3), nut on gearbox output shaft

should be torqued to 450 ft-lbs. minimum and cotter
pin installed in nut with legs securely bent around
nut.

Driveline Protection

The drivetrain is protected from shock loads with a four
plate slip-clutch. The slip-clutch must be capable of
slippage during operation. Always do a “clutch run-in”
operation at the beginning of each season and after long
periods of inactivity to remove any oxidation that may
have accumulated on the friction surfaces. Repeat
“clutch run-in” instructions when moisture and/or
condensation seizes the inner friction plates.

WARNING

!

Always shut tractor down using “Tractor Shutdown

Procedure” provided in this manual before dismounting

Clutch Run-In

Refer to Refer to Figure 5-3:

1.

Using a pencil or other marker, scribe a line across the
exposed edges of the clutch plates and friction

discs.

Clutch

Figure 5-3

2. Carefully loosen each of the 8 spring retainer nuts by

exactly 2 revolutions. It will be necessary to hold hex
end of retainer bolt in order to count the exact
number of revolutions.

3. Start tractor and engage power take-off drive for 2-3

seconds to permit slippage of the clutch surfaces.
Disengage power take-off, then re-engage a second
time for 2-3 seconds. Disengage power take-off, shut
off tractor, and remove key. Wait for all components to
stop before dismounting from tractor.

13693

«
...
27
28
29
30
31
...
»

Содержание RCR2660









































Отзывы:

Нет отзывов