Land Pride RCR2660 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 40

Land Pride RCR2660 Скачать руководство пользователя страница 17

Section 1: Assembly & Set-up

Table of Contents

12/4/18

RCR2660 and RCR2672

Rotary Cutters

13

6. Attach tail wheel adjusting bracket (#5) to tail wheel

mounting brackets (#6 & #7) with two 1/2" x 1 1/2"
round head square neck bolts (#11), flat
washers (#12), and locknuts (#14) as shown. Final
adjustments to the tail wheel height are outlined
under

“Tail Wheel Height Adjustment”

Check Chain Option

Refer to Figure 1-10:

Install check chain to the cutter as with 3/4" x 1 1/2" grade
5 hex head cap screws and 3/4" nuts with spring lock
washers as shown. Tighten all nuts and bolts to correct
torque. See

“Torque Values Chart”

Front and Rear Safety Guard Options

DANGER

!

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front and rear safety guards is

mandatory with this cutter. Stop blade rotation if a bystander

is in or around the area.

WARNING

!

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Front Safety Guard

Refer to Figure 1-11:

Install front chain or rubber guard as shown using
3/8" x 2 3/4" long round head square-neck bolts (#1) and
3/8" locknuts (#2). Tighten all nuts and bolts to correct
torque. See

“Torque Values Chart”

Rear Chain Guard

Refer to Figure 1-12:

Install each segment of the rear chain guards as shown
using 1/2" X 1 1/4" round head bolts (#1), 1/2" flat
washers (#2), and 1/2" locknuts (#3). Tighten all nuts and
bolts to correct torque. See

“Torque Values Chart”

on

Check Chain Installation

Figure 1-10

Front chain Guard

Figure 1-11

Rear Chain Guard

Figure 1-12

20959

20949

20953

«
...
15
16
17
18
19
...
»

Содержание RCR2660









































Отзывы:

Нет отзывов