background image

1

© Copyright 2010

Printed

Before You Start

The Baffle Kit and Shredder Kit are exclusively designed
for your 20’ Land Pride Rotary Cutter. Please read these
installation instructions and your Rotary Cutter
Operator’s Manual thoroughly before beginning.
Especially read information relating to safety concerns.
Also included in the Operator’s Manual is important
information on operation, adjustment, troubleshooting,
and maintenance for this attachment (some manual
sections do not apply to all accessories).

A separate Rotary Cutter Parts Manual is available free
of charge at www.landpride.com or can be purchased
from your nearest Land Pride dealer. Have the model
and serial numbers of your cutter handy when placing an
order.

Manual Part Numbers:

• Operator’s Manual . . . . . . . . . . . . . . . . . 318-474M

• Parts Manual . . . . . . . . . . . . . . . . . . . . . 318-474P

General Information

These assembly instructions apply to the Baffle and
Shredder Kits listed below:

330-309A

SHREDDER/FIXED BLADE/BAFFLE

330-114A

BAFFLES, FRONT

330-308A

SHREDDER/FIXED BLADE

330-585A

BAFFLES, REAR

Tools required:

Safety Glasses

Work Gloves

Two 3/4" wrenches . . . . . . . . . . . . . . . . . Baffle Kit Only

Two 1 1/2" wrenches  . . . . . . . . . . . . Shredder Kit Only

One 55mm wrench . . . . . . . . . . . . . . Shredder Kit Only

When you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!

!

IMPORTANT: Before you begin, read these
instructions and check to be sure all parts and tools
are accounted for. Please retain these installation
instructions for future reference and parts ordering
information.

Further Assistance

Your dealer wants you to be satisfied with your new
Baffle and Shredder Kits. If for any reason you do not
understand any part of this manual or are not satisfied
with the service received, the following actions are
suggested:

1. Discuss the matter with your dealership service

manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.

2. If you are still not satisfied, seek out the owner or

general manager of the dealership, explain the
problem and request assistance.

3. For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

[email protected]

Safety Information

!

DANGER

Always disconnect main driveline from tractor PTO before
servicing cutter deck. Cutter can be engaged if tractor is
started resulting in cutter damage, bodily injury and/or death.

!

WARNING

Never work under equipment supported by hydraulics.
Hydraulics can drop equipment if controls are actuated or if
hydraulic lines burst. Either situation can drop the cutter
instantly even when power to the hydraulics is shut off.

Assembly Instructions

A detailed listing of parts for the Baffle and Shredder Kits
is provided on pages 10 & 11. Use the list as a checklist
to inventory parts received. Please contact your local
Land Pride dealer for any missing hardware.

1. Cutters with Serial No. 536742 and lower:

Lower cutter and wings to the lowest position.

Cutters with Serial No. 536743 and above:
Raise wings fully up and lock into position with
transport locks.

IMPORTANT: Read all "Safety Information" above
before working on and around the cutter decks.

For RC(M)5020 Rotary Cutters

Baffle and Shredder Kits

3/11/10

Manual No. 330-148M

All manuals and user guides at all-guides.com

all-guides.com

Содержание RCM5020 Series













Отзывы: