manualshive.com logo in svg

Land Pride RCM3712, Руководство оператора

Поделиться
Скачать
Land Pride RCM3712 Скачать руководство пользователя страница 40

Section 4: Options & Accessories

RC(M)3712 & RCG(M)3712 Rotary Cutters 334-203M

11/6/18

36

Table of Contents

Section 4: Options & Accessories

Safety Chain Guards

DANGER

!

To avoid serious injury or death:  Rotary Cutters have the 

ability to discharge objects at high speeds; therefore, the use 

of front and rear safety guards are required with this cutter. 

Specifically, double row chain guards should be used when 

cutting along roadways and in areas where people may be 

present. Stop blade rotation if bystanders are in or around the 

area.

Land Pride offers two types of safety chain guards to best 
suit your application: single row chain guards and double 
row chain guards.

•

Single row chain guards are constructed with a single 
row of hanging chain links. They can withstand harsh 
applications. 

•

Double row chain guards are constructed with rows of 
doubled over hanging chain links. The extra chain 
provides an additional barrier for stopping thrown 
objects.

Single Chain Guards

334-194A

Single Row Chain Guards

Double Chain Guards

334-195A

Double Row Chain Guards

Tire & Axle Arrangements

Land Pride offers three different tires and two axle 
arrangements to best suit your application:

•

Laminated tires: They are constructed of laminated 
layers of solid rubber that will never go flat. 

•

New foam filled tires: They are built tough to withstand 
the rugged use a cutter receives, provides a smoother 
ride when transporting and won’t go flat.

•

New aircraft tires: They are built tough to withstand the 
rugged use a cutter receives and to provide a smoother 
ride when transporting. 

•

4 - Wheel axle arrangement: Two tires on transport 
axle and one on each wing axle.

•

6 - Wheel axle arrangement: Four tires on transport 
axle and one on each wing axle.

Hitches

Land Pride offers 5 different hitches to best suit your 
application. See 

“Hitch Types” 

on page 12 for complete 

description of optional hitches. 

334-463A

Fixed Clevis Hitch

334-460A

Bar-Tite Hitch

334-462A

Ball Hitch

334-470A

Fixed Pintle Hitch

334-471A

LP Performance Hitch

Main Drivelines

Land Pride offers two different CAT 6 main drivelines to 
best suit your application.

•

CAT 6 constant velocity drivelines allow the operator to 
make 80 degree turns. They are heavy duty long 
lasting drivelines.

•

CAT 6 constant velocity drivelines with overrunning 
clutch have the same features as the CAT 6 constant 
velocity driveline plus the overrunning clutch feature. 
The overrunning clutch protects the tractor’s power 
take-off on tractors that have instant off power take-
offs by allowing the cutter to slowly stop the blades 
without putting strain on your tractor power take-off.

CAT 6 Constant Velocity

826-643C

CAT 6 CV driveline

CAT 6 Constant Velocity With Overrunning Clutch

826-884C

CAT 6 CV with overrunning clutch driveline

Содержание RCM3712

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды