Land Pride RC5610 Series Скачать руководство пользователя

Страница: 44 / 70

Section 4: Options & Accessories

RC5610, RC6610, RCM5610, & RCM6610 Series 2 S/N Rotary Cutters 330-539M

5/6/20

Table of Contents

Section 4: Options & Accessories

Safety Guards

DANGER

To avoid serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Double row chain guards should

be used when cutting along roadways and in areas where

people may be present. Stop blade rotation if bystanders are in

or around the area. It is recommended that a safety shield be

placed between the operator and cutter on an open air tractor.

WARNING

To avoid serious injury or death:
Keep all safety guards in place. Rotary Cutters have the

ability to discharge objects at high speeds. Use extreme

caution when cutting in areas where people may be present. It

is best to operate the cutter when no one is nearby. Stop blade

rotation if someone is in or around the area.

Land Pride offers four types of safety guards to best suit

your application: rubber skirt guards, single row

chainguards, double row chainguards, and double row

chainguards with cable.

•

Rubber skirt guards are designed for light duty

applications.

•

Single row chainguards are constructed with a single

row of hanging chain links. They can withstand harsher

applications than rubber skirts.

•

Double row chainguards are constructed with two

staggered rows of hanging chain links. The second row

provides an additional barrier for stopping thrown

objects.

•

Double row chainguards with cable are constructed

with a double row of hanging chain links and a steel

cable threaded through the bottom hanging chain links.

This restricts the hanging links from spreading apart

when hit by solid objects.

Rubber Guards

330-513A Front Rubber Safety Guards
330-525A Rear Rubber Safety Guards

Single Row Chain Guards

330-512A Front Single Row Chainguards
330-524A Rear Single Row Chainguards

Double Row Chain Guards

330-514A Front Double Row Chainguards
330-526A Rear Double Row Chainguards

Double Row Chain Guards with Cable

330-515A Front Double Row Chainguards with Cable
330-527A Rear Double Row Chainguards with Cable

Low Lift Blade Accessory

Land Pride recommends low lift blades when cutting tall

Johnson Grass, weeds, and brush as they provide a

better quality of cut when cutting these materials. See

Figure 5-8 on page 46 for low lift blade part numbers.

Tire & Axle Arrangements

Land Pride offers four different tire options and two axle

arrangements to best suit your application:

•

Laminated tires: They are constructed of laminated

layers of solid rubber that will never go flat.

•

New tires: They are available in foam filled and air

filled. Both are built tough to withstand the rugged use

a cutter receives and to provides a smoother ride when

transporting. Foam filled tires won’t go flat.

•

Used aircraft tires: They are built tough to withstand

the rugged use a cutter receives and to provide a

smoother ride when transporting.

•

5- Wheel standard axle arrangement: Four on

transport axle and one wing axle.

•

6 - Wheel standard axle arrangement: Four on

transport axle and two on wing axle.

Hitches

The cutter is factory supplied with the standard clevis

hitch. Other optional hitches are available. See

“Hitch

Types”

on page 15 for description of all hitches.

330-225A Standard Clevis Hitch
330-333A Bar-Tite Hitch (Optional)
330-335A Ball Hitch (Optional)
330-334A Pintle Hitch (Optional)
334-045A LP Performance Hitch (Optional)

Содержание RC5610 Series







































































Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды

Land Pride RC5610 Series, Руководство оператора

Результаты поиска

Содержание RC5610 Series

Отзывы:

Похожие инструкции для RC5610 Series

Бренды по названию

Популярные бренды