manualshive.com logo in svg

Land Pride RC5010, Руководство оператора, Страница: 40 / 46

Поделиться
Скачать
Land Pride RC5010 Скачать руководство пользователя страница 40

38

RC5010 & RC6010 (540 RPM) and RCM5010 & RCM6010 (1000 RPM) Rotary Cutters   318-128M

8/28/08

Land Pride

Section 6: Specifications & Capacities

Table of Contents

Section 6:

Specifications & Capacities

RC5010, RCM5010, RC6010 & RCM6010 Series

RC5010 & RCM5010

RC6010 & RCM6010

Cutting Width

Overall Width

Minimum Transport Width

10’-0”
11’-0”

8’-0”

10’-0”
11’-0”

8’-0”

Cutting Height

2” - 14”

Overall Length

15’-1"

Deck Material Thickness

10 gauge

3/16”

Deck Rings

Optional

Deck Height

10 1/2”

Hitch Type

Pull Type, Self - Leveling Hitch & Clevis

Hitch Options

Standard Clevis, Double Swivel or Bar-Tite

Blades - 4(2 per Carrier)

1/2” x 4” Heat Treated Alloy Steel

Free Swinging with up lift

Blade Tip Speed @ 540 RPM

Center Blade

Wing Blade

14,909 FPM

5,307 FPM

15,268 FPM
15,000 FPM

Blade Tip Speed @ 1000 RPM

Center Blade

Wing Blade

15,606 FPM
14,651 FPM

15,578 FPM
14,620 FPM

Blade Holders

Wing & Center: 3/16”, Round, Dish Shaped

Debris Guards

Rubber, Single or Double Chain

Input Drive Line

540 PTO: ASAE Category 5

1000 PTO:ASAE Category 5

Connecting Driveline

Cat.4 Slip-Clutch

Gear Boxes

250 HP

Wheel Options

6” x 21” Laminated or

15” Rims or

24” x 7.7” x 15” Used Aircraft Tires

Center Axle Options

Walking Tandem

Shock Load Suspension

Springs on center axle

Machine Weight (With front / rear chain

guards)

3,417 lbs. Approx.

3,600 lbs. Approx.

Tongue Weight

1,350 lbs.

Tongue Jack

Standard

Min. PTO Horse Power

50

Содержание RC5010















































Отзывы:

Нет отзывов