Land Pride RC3615 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 54

background image

Table of Contents

RC3615 (540 RPM) and RCM3615 (1000 RPM) Rotary Cutters 330-502M

4/20/15

©

Copyright 2015 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 10
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 10

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Section 1: Assembly & Set-up . . . . . . . . . . . 11

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . 11

Horsepower  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Drawbar Set-up   . . . . . . . . . . . . . . . . . . . . . . . . . 11
PTO Speed   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hydraulic Outlets  . . . . . . . . . . . . . . . . . . . . . . . . 11

Before You Start  . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Hitch Types  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Standard Clevis Hitch . . . . . . . . . . . . . . . . . . . . . 12
Double Swivel Clevis Hitch (Optional)   . . . . . . . . 12
Bar-Tite Hitch (Optional)   . . . . . . . . . . . . . . . . . . 12
Ball Hitch (Optional)  . . . . . . . . . . . . . . . . . . . . . . 12
Pintle Hitch (Optional)   . . . . . . . . . . . . . . . . . . . . 12

Hitch & Jack Assembly   . . . . . . . . . . . . . . . . . . . . . 13
Turnbuckle Assembly   . . . . . . . . . . . . . . . . . . . . . . 13
Standard Clevis Hitch Hook-up  . . . . . . . . . . . . . . . 14
Double Swivel Clevis Hitch Hook-up  . . . . . . . . . . . 15
Bar-Tite Hitch Hook-up   . . . . . . . . . . . . . . . . . . . . . 16
Driveline Installation   . . . . . . . . . . . . . . . . . . . . . . . 17
Hydraulic Hook-up . . . . . . . . . . . . . . . . . . . . . . . . . 17
Purge Hydraulic System   . . . . . . . . . . . . . . . . . . . . 18
Unhook Rotary Cutter  . . . . . . . . . . . . . . . . . . . . . . 18

Section 2: Adjustments . . . . . . . . . . . . . . . . . 20

Center & Wing Section Leveling . . . . . . . . . . . . . . 20

Center Deck Leveling . . . . . . . . . . . . . . . . . . . . . 20
Wing Deck Leveling . . . . . . . . . . . . . . . . . . . . . . 21

Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . 21

Section 3: Operating Instructions . . . . . . . . 22

Startup Checklist  . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tractor & Cutter Inspection  . . . . . . . . . . . . . . . . . . 23
Blade Operation Inspection  . . . . . . . . . . . . . . . . . . 24
Transport Locks   . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Lower Wing Down & Set Cutting Height  . . . . . . . 26
Set Wing Lift Lever In Float Position   . . . . . . . . . 26
Select Gear Range . . . . . . . . . . . . . . . . . . . . . . . 26
Engage Blades . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Disengage Blades   . . . . . . . . . . . . . . . . . . . . . . . 27
Avoid Extreme Turning Angles  . . . . . . . . . . . . . . 27

General Operating Instructions . . . . . . . . . . . . . . . 27

Section 4: Options & Accessories . . . . . . . . 29

Safety Guard  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Tire Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Hitch Options  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Hydraulic Accessories  . . . . . . . . . . . . . . . . . . . . . . 30

Hydraulic Wing Control Kit . . . . . . . . . . . . . . . . . 30
Selector Control Valve Kit . . . . . . . . . . . . . . . . . . 30

Mechanical Wing Lift . . . . . . . . . . . . . . . . . . . . . . . 31

Section 5: Maintenance & Lubrication . . . . . 32

General Maintenance Information  . . . . . . . . . . . . . 32
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . . 32
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 32
Drivelines With Slip Clutches  . . . . . . . . . . . . . . . . . 34

Type A Clutches . . . . . . . . . . . . . . . . . . . . . . . . . 34
Type B Clutches . . . . . . . . . . . . . . . . . . . . . . . . . 36

Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . . 37

Center Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . 37
Wing Skid Shoes . . . . . . . . . . . . . . . . . . . . . . . . 37

Tire Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Long Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 38
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 39
Lubrication Points   . . . . . . . . . . . . . . . . . . . . . . . . . 40

Axle Hub Bearing  . . . . . . . . . . . . . . . . . . . . . . . . 40
Adjustable Turnbuckle   . . . . . . . . . . . . . . . . . . . . 40
Hitch Frame  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Center Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Wing Axle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Double Swivel Clevis Hitch (Optional)   . . . . . . . . 41
Bar-Tite Hitch (Optional) . . . . . . . . . . . . . . . . . . . 41
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Divider Box  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wing Driveline Profile Tubes   . . . . . . . . . . . . . . . 43
Wing Driveline Joints & Shields   . . . . . . . . . . . . . 43
Intermediate Driveline Joints   . . . . . . . . . . . . . . . 43
Conventional Driveline Profile Tubes  . . . . . . . . . 44
Conventional Driveline Joints & Shields  . . . . . . . 44
CV Main Driveline Profile Tubes  . . . . . . . . . . . . . 44
CV Main Driveline Joints   . . . . . . . . . . . . . . . . . . 44

Accessing CV Driveline Joints . . . . . . . . . . . . . 45

Section 6: Specifications & Capacities . . . . . 46
Section 7: Features & Benefits  . . . . . . . . . . . 48
Section 8: Troubleshooting  . . . . . . . . . . . . . . 49
Section 9: Torque & Tire Inflation Chart  . . . . 50
Section 10: Warranty  . . . . . . . . . . . . . . . . . . . 51

«
1
2
3
4
...
»

Содержание RC3615























































Отзывы:

Нет отзывов

Похожие инструкции для RC3615

Бренд: MacDon Страницы: 17

Бренд: Olympus Страницы: 50

Бренд: VAHVA Страницы: 19

Бренд: ParaBody Страницы: 5

Бренд: Baileigh Industrial Страницы: 28

Бренд: Baileigh Industrial Страницы: 56

Бренд: Kawai Страницы: 10

Бренд: Faderfox Страницы: 8

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Federal Signal Corporation Страницы: 4

Бренд: FEBER Страницы: 2

Бренд: FASTERHOLT Страницы: 96

Бренд: Farmi Forest Corporation Страницы: 32

Бренд: IBS Scherer Страницы: 64

Бренд: HALDER Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды