Land Pride 3P806NT Скачать руководство пользователя страница 78

Страница: 78 / 92

Appendix B - Pre-Delivery

Table of Contents

3P806NT 313-520M

2019-01-23

Caster Shaft Installation

Refer to Figure 45 and Figure 46

Begin Install Shaft

11. Select one each:

161

116D LIFT ASSIST CASTER SHAFT

Insert caster shaft

through caster frame plate

and secure with bolt

and nut

Install Lock Out Plunger

12. Select one each:

807

175C SPRING COMP .796ODX.065WX1.

151

355D 1007 LOCK OUT PLUNGER

805

076C PIN ROLL 3/16 X 1 3/4 PLT.

Place lock out plunger spring

over lock out

plunger

. Inserting from the bottom up of plunger

tube , force both into the plunger tube and secure

with roll pin

Note: The lock out plunger tube MUST be facing to the

front of the drill. If it is facing to the rear, the pivot

arm tube is on backwards and must be switched.

Finish Install Shaft

13. Select one each:

161

056D CASTER SPACER

161

114D CASTER RETAINER CAP

and two each:

890

072C BUSHING 2 1/2 X 2 1/4 X 2 LG.

015C WASHER LOCK SPRING 1/2 PLT

Place spacer

over the top of the caster shaft

With mallet, drive one bushing

into shaft hole on

bottom of pivot arm tube and one in top of hole on

pivot arm tube. Place shaft up through these bushings

in pivot arm. Complete assembling shaft by placing

caster retaining cap

on top and securing with two

washer lock springs

and two bolts

Install Lock Tube

14. Select one each:

266

020D UHMW RND 2.0 DIA X 2.0 LONG

807

143C SPRING COMP 1.88OD X .36 +

266

012D PLATE RND 3/16" THK 1 7/8"

Assemble bushing

, spring

and small round

plate

. Push up inside lock tube. Complete with

nut

and bolt

Install Caster Zerks

15. Select one:

800

001C GREASE ZERK STRAIGHT 1/4

Install zerk

in shaft at end of pivot arm tube.

16. Repeat all steps for other caster.

Figure 45

Caster Shaft Installation

32115

Figure 46

Caster Assembled

32119

36
78
35
53
64

Содержание 3P806NT





























































































Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 3P806NT, Руководство оператора

Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды