Land Pride 3P806NT Скачать руководство пользователя страница 49

Страница: 49 / 92

Maintenance and Lubrication

Table of Contents

2019-01-23

3P806NT 313-520M

Chain Maintenance

Initially check the drive chains after the first 10 hours of

drill use. The slack of new chains tends to increase

during the first few hours of operation due to seating.

Thereafter, check the chains every 100 hours.
Lubricate chains any time there is a chance of moisture,

and when being stored at the end of the planting season.

Chain Slack

Refer to Figure 34, which, for clarity, greatly exaggerates

slack, and omits the idlers.

1. Measure the span

for allowable slack:

Locate the longest span of each chain (usually the

span which does not run through the idlers).

2. Determine the ideal slack:

Long chains (over 36 in. / 91cm):

in. per ft. (21 mm/m)

Vertical short chains:

in. per ft. (21 mm/m)

Horizontal short chains:

in. per ft. (42 mm/m)

3. Measure the current slack :

Acting at a right angle to the chain span at the center

of the span, deflect the chain in both directions. The

slack is the distance of the movement.

4. Adjust the idlers for ideal slack.
Whenever mounting a chain, make sure the clip at the

removable link is oriented to minimize snags.

Refer to Figure 35 (arrow shows chain direction)

Install clip with open end facing away from direction of

chain travel (shown by gray or striped arrows in chain

routing diagrams).

Seed Flap Replacement

Refer to Figure 36

To replace a seed flap , use needle nose pliers or

similar tool to grasp “T” top of flap. Pull upward to

remove flap from metal bracket .
Push new seed flap down through metal bracket

until flap snaps into place with “T” top resting on top of

bracket.
If a seed firmer is also installed, it may be necessary to

shorten the flap.

Figure 34

Measuring Chain Slack

27264

Figure 35

Chain Clip Orientation

26482

Figure 36

Seed Tube Flap

31047

Содержание 3P806NT





























































































Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды

Land Pride 3P806NT, Руководство оператора

Результаты поиска

Содержание 3P806NT

Отзывы:

Бренды по названию

Популярные бренды