Page 42
Maintenance interval every 4,000 operating hours
Deadly risk!
Switch off operating voltage,
Unscrew or disconnect back-up fuse!
Risk of injury!
Prior to operation, depressurise the equipment by opening the safety valve "high pressure" (25)!
Risk of injury!
Caution with heated components!
• Prepare tools: 1 allen screw driver 3/16“ (LANCIER Monitoring order no. 020657.000),
1 combination wrench 19 mm and 1 steel ruler
• Open cabinet door.
• Close shut-off valve (
9
).
The
line item numbers
(
bold, italic
, not in brackets) in chapter "1 Servicing compressor" relate to the explod-
ed drawing of the compressor on opposite page.
1. Servicing compressor VD 7/2 (RTS 1000D) and VD 28/2 (RTS 2600D)
1.1 Dismount compressor
• Detach hose clip from pressurised air hose.
• Remove pressurised air hose.
• Undo fastening screw of compressor.
• Pull compressor out.
• Branch off the electricity from the compressor's junction plate or disconnect coupling (option) of electrici-
ty from the compressor.
• Take out compressor.
1.2 Disassemble compressor
• Unscrew fan cap
39.
• Loosen connecting nut
41
on L-piece
17
of the cylinder head
20
.
• Undo cylinder head screws
18
.
• Remove cylinder head
20
, suction and pressure valves with seals
21-25
.
• Undo fastening screws
18B
of cylinder
26
and remove cylinder from pistons.
1.3 Clean and if necessary replace compressor parts
• Dry clean all parts.
• Replace damaged or worn valves.
• Replace seals for cylinder and cylinder head.
1.4 Assemble compressor
• Replace piston rings
28
and springs
29
.
• Fit both piston rings
28
turned 180°!
• Replace backer strip
31
.
• Put on cylinder
26
and screw tightly (max. 10 Nm)!
The piston must not project out of the cylinder in the top dead centre position. (check with ruler!)
• Place cylinder head, suction and pressure valves with seals
21-25
on cylinder
26
.
Pay attention to the order of suction and pressure valve platess and marking holes.
• Insert and tighten cylinder head screws
18
. Do not tighten screws too much (10 Nm)!
• Fasten connecting nut
41
on L-piece
17
of the cylinder head
20
.
• Screw on fan cap
39
.
1.5 Change air intake filter (see page 38)
• Turn and pull filter cap to the left.
• Replace filter cartridge
5
.
• Put on filter cap again and tighten.
1.6 Mount compressor
• Place compressor in front of equipment.
• Connect electricity.
• Place compressor into the equipment.
• Turn in and tighten mounting bolts.
• Mount pressurised air hose and tighten with hose clip.
Содержание RTS 1000D
