Lamtec ETAMATIC страница 52 Скачать руководство пользователя

Страница: 52 / 136

O2-Control

6.14

Re-enter Range Limits

If you change the limit switches after the programming, you must determine the range limits
again.
Enter password (see chapter 5.1.2 Password Entry).

Since no point has been entered, the old curve is re-activated, but the range limits remain
cleared.
Now allow the system to pre-ventilate.



Range limits are re-entered.

NOTICE!
You can see this in the "Set-point" display. Without limits the set-point is 0 or 999. Once the
limit is determined, the set-point skips to the actual value.

Press key 14



the display shows "SL" in its center

Press key 11 ENTER



the display shows "cleared".



The curves and the range limits are deleted.

Press key 13 twice



the display shows "restore previous curve ?"

Press key 7

Содержание ETAMATIC









































































































































Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды

Lamtec ETAMATIC, Руководство пользователя

Результаты поиска

Содержание ETAMATIC

Отзывы:

Похожие инструкции для ETAMATIC

Бренды по названию

Популярные бренды