Lamtec ETAMATIC Скачать руководство пользователя страница 34

Страница: 34 / 136

Commissioning

Clear Memory

5.2.3

Programming the Ignition Point

5.2.4

Programming the Base Load

Program 3

to 10

point

Proceed as described in "Program base load point", but run to each of the load ratings “250",
"300", "400", "500", "600", "700", "800", "900", and "999" one after the other.

Press key 16 twice ("Set-point" display)

Press key 14 twice



the display shows SL in its centre.

Press Enter key 11 “ENTER”



the display shows "cleared", the old curve is

cleared. Start burner (signal at terminal 58) and wait until pre-ventilation has ended.

Press key 13



the display shows "El" in its center

Use keys 16 and 17 to switch to "setpoint"

Use keys 2 to 9 to run the control elements to ignition position

Press key „ENTER“



the display shows "Really ignite"

If not, press key 3 and redefine ignition position.

Press key “ENTER” again to confirm.



Burner ignites.

Use keys 16 and 17 to switch to "load value"

Use keys 2 and 3 to set "200"

Use keys 16 and 17 to switch to "setpoint"

Use keys 2 to 9 to run control elements to base load position.

Press key ENTER .

Press key ENTER to store the curve.
Press key 13 (switch unit from "Set" to "Automatic").





the display shows "memory"

Содержание ETAMATIC









































































































































Результаты поиска

Содержание ETAMATIC

Отзывы:

Бренды по названию

Популярные бренды

Lamtec ETAMATIC, Руководство пользователя

Результаты поиска

Содержание ETAMATIC

Отзывы:

Бренды по названию

Популярные бренды