LAMPHUS
®
Cruizer
TM
Series
CREE
®
LED Flood/Spot Off Road Light Bar
(CRLB06, CRLB12, CRLB24, CRLB42, CRLB78, CRLB96)
SKU: ORZLEDLBR104, 107, 112, 122, 136, 144
www.online-led-store.com
US Toll Free: 1-855-LED-ONLINE (533-6654)
International: 1-909-212-0993
Fax: (909) 575-6722
E-mail: [email protected]
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
•
Proper installation of this product requires the installer to have a good understanding of
automotive electronics, systems, and procedures.
•
If mounting this product requires drilling holes, the installer MUST be sure that no vehicle
components or other vital parts could be damaged by the drilling process. Check both sides of the
mounting surface before drilling begins. Also de-burr any holes and remove any metal shards or
remnants. Install grommets into all wire passage holes.
•
If this manual states that this product may be mounted with suction cups, magnets, tape or
Velcro®, clean the mounting surface and dry thoroughly prior to apply adhesive for maximum
adhesion.
•
Do not attempt to activate or control this device in a hazardous driving situation.
•
Do not install this product or route any wires in the deployment area of your air bag. Equipment
mounted or located in the air bag deployment area will damage or reduce the effectiveness of the
air bag, or become a projectile that could cause serious personal injury or death. Refer to your
vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full
responsibility to determine proper mounting location, based on providing ultimate safety to all
passengers inside the vehicle.
•
This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination
of these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage
could result.
Contents
Model
Light Unit
Accessory Pack
CRLB06
1
1
CRLB12
1
1
CRLB24
1
2
CRLB42
1
2
CRLB78
1
3
CRLB96
1
3
Accessory Pack Content
Swivel Mounting Bracket
1
Bolt for Mounting
1
Nut for Mounting
1
Split Washer for Mounting
1
Bolt for Light Unit
4
Nut for Light Unit
4
Flat Washer for Light Unit
4
Split Washer for Light Unit
4
Specifications by Model
Input Voltage: 12 – 30 VDC
Model
Amperage @ 12 VDC
Output Wattage
CRLB06
1
18
CRLB12
2
36
CRLB24
4
72
CRLB42
8
126
CRLB78
16
234
CRLB96
20
288
Mounting
CAUTION! Permanent mounting of this product will require drilling. It is
absolutely necessary to make sure that no other vehicle components could
be damaged by this process. Check both sides of the mounting surface
before starting. If damage is likely, select a different mounting location.
1.
Select a desired mounting location. Make sure there is at least 5” of clearance in order for
the light to fit properly over the mounting location.
2.
Place the Swivel Bracket over the desired mounting surface.
3.
Mark the area where the mounting holes are to be drilled. Confirm that no vehicle parts
could be damaged by the drilling process.
4.
Using a drill bit of appropriate size, drill a mounting hole for the Mounting Bolt. Thoroughly
de-burr all hole(s).
5.
Secure the Swivel Bracket onto the mounting surface using the included Mounting Bolt, Nut,
and Washer.
6.
Secure the light unit onto the Swivel Bracket using the included Bolt, Nut, and Washer for
Light Unit,
7.
Adjust the light unit to the desired tilt angle prior to tightening the Nuts all the way.
Wiring
WARNING! All customer supplied wires that connect to the positive terminal
of the battery must be sized to supply at least 125% of the maximum
operating current and FUSED at the battery to carry that load. DO NOT USE
CIRCUIT BREAKERS WITH THIS PRODUCT!
RED – To 10-30 VDC Power Source
BLACK – To Chassis Ground
Online LED Store S2B Inc. ©2013 All Rights Reserved
