background image

14

3.2 Preparing the Meter for Calibration

For the best results, select a standard with a concentration close to the 

concentration of the sample being measured. Alternatively, a calibration 

standard with a concentration that is approximately 2/3 the full-scale 

of the measurement range.  For example, in the 0 to 2000 

μ

S/cm 

conductivity range, use a 1413 

μ

S/cm standard for calibration. 

Use fresh calibration standards. Reuse of standard solutions may impair 

the calibration and the accuracy of measurements. Store solutions in a 

dry, dark, cool environment and limit exposure to air. 
Rinse or immerse the probe in clear water before calibration and between 

samples. Deionized water is ideal. 

3.3 Selection of Auto or Manual Calibration (CON 6 PLUS)

The CON 6 PLUS is capable of automatic or manual calibration. The 

factory default setting is automatic.  
In the automatic calibration mode, the CON 6 PLUS will automatically 

select one of four calibration standard values (see below) depending on 

the range and normalization temperature being used. 
Automatic calibration is useful when all of the calibration standards 

fall into one of the groups listed below. For example, if the 1413 

μ

S/

cm standard reads as 1400 

μ

S/cm during calibration, press “ENTER” to 

accept this value as 1413 

μ

S/cm using the automatic mode. In manual 

mode, the increment button would have had to be pressed 13 times to 

adjust the value to 1413 

μ

S/cm to before pressing “ENTER”. 

Normalization 

Temperature

Calibration Standards (Range)

25 °C

1. 84 

μ

S/cm (for 0 – 200 

μ

S/cm)

2. 1413 

μ

S/cm (for 0 – 2000 

μ

S/cm)

3.  12.88 mS/cm (for 0.00 – 20.00 mS/cm)
4.  111.8 mS/cm (for 0.0 – 200.0 mS/cm) 

20 °C

1. 76 

μ

S/cm (for 0 – 200 

μ

S/cm)

2. 1278 

μ

S/cm (for 0 – 2000 

μ

S/cm)

3.  11.67 mS/cm (for 0.00 – 20.00 mS/cm)
4.  102.1 mS/cm (for 0.0 – 200.0 mS/cm)

       Table 1: Conductivity Calibration Standards for Auto Calibrations

If a calibration standard is used that is not listed above, select manual 

calibration. 

Содержание CON 6 PLUS





































Отзывы: