Lambrecht Ser[LOG] Скачать руководство пользователя страница 15

Страница: 15 / 129

LAMBRECHT meteo GmbH

Ser[LOG] Manual

Page 15 of 129

1.2

Description AnDiMod · Measurement module for analogue / digital

sensors

There are three different extension modules for the Ser[LOG] and Ser[LOG]Plus. The modules AnDiMod

1-3 differ in their address on the Ser[LOG] bus. If a Ser[LOG] system is extended with an AnDiMod

module, a prior examination is necessary to determine how many modules have already been connected

and that these modules have been assigned with the correct addresses (the numbering follows). The

first module (upon extending a Ser[LOG]) must carry address 1. The first module (upon extending a

Ser[LOG]Plus) must carry address 2, since AnDiMod with address 1 in Ser[LOG]Plus is already inte-

grated. The respective address of AnDiMod is fixed and cannot be customized by the user.

Sensor supply

Terminal clamp AnDiMod

Digital inputs

Analog inputs

Analog inputs

An AnDiMod has 12 universally configurable analogue inputs. The channels can

be set for the measuring ranges:

●

5 V bipolar,

●

5V unipolar,

●

50 mV bipolar,

●

20 mA

●

500 ohms

●

5000 ohms.

For the measurement of 20mA signals, a measuring resistor (shunt) must be

switched on. This is done by setting a bridge in the upper two terminals.

Digital Inputs

The inputs "D1", "D2" and "D3" are for connecting digital sensors. They can be used

to capture:

Содержание Ser[LOG]


































































































































Результаты поиска

Содержание Ser[LOG]

Отзывы:

Похожие инструкции для Ser[LOG]

Бренды по названию

Популярные бренды

Lambrecht Ser[LOG], Руководство оператора

Результаты поиска

Содержание Ser[LOG]

Отзывы:

Похожие инструкции для Ser[LOG]

Бренды по названию

Популярные бренды