Laird OL 4503 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 36

Laird OL 4503 Скачать руководство пользователя страница 18

18

5. Transport

5.1 Safety Indications for Transportation and Setting-up

CAUTION

Risk of injury by lifting the unit!
The weight of the unit is more than 50 kg.



Do not lift the unit manually!



Always use proper auxiliary means such as a forklift or a jack lift!

5.2 Transportation of the Unit

The unit is delivered wrapped in foil on a transportable pallet. Leave the unit on the pallet until

bringing it into service. Use a forklift or jack lift for transportation to the installation location.

CAUTION

Risk of damage by improper transportation!



Transport the unit in upright position.



Do not tilt the unit or expose it to impacts.

5.3 Unpacking

Remove the foil before setting up the unit!
Inspect the unit regarding:



Damage caused by transportation



Completeness of delivery

Lift the unit with a forklift or jack lift off the transportable pallet.
Dispose of the packaging material in accordance with regional regulations.

NOTE

Laird Thermal Systems advises to keep the transportable pallet for later transportation of the unit.

«
...
16
17
18
19
20
...
»

Содержание OL 4503





































Отзывы:

Нет отзывов