Laird BTM511 страница 30 Скачать руководство пользователя

Страница: 30 / 46

www.lairdtech.com

Laird Technologies

BTM510/511

Bluetooth

Multimedia Module

CONFIgurINg

THE BTM510/511

3. Mic Input Gain

A microphone preamplifier which adds extra 20dB to input gain, is controlled by S-Register 415.

4. Mic Bias

Mic Bias will be enabled with S-Register 416.

Mic Bias Current is controlled by S-Register 417.

Mic Bias Voltage is controlled by S-Register 418.

5. Auxiliary DAC

The auxiliary DAC is enabled with S-Register 730.

The DAC output level is set by S-Register 731.

6. LED

The BT-MM module provides two dedicated output pins for LEDs (LED_EXT0, LED_EXT1).

Following modes are supported: LED_OFF, LED_ON, LED_PWM and LED_PULSE.

In LED_PWM mode, the parameters “Duty Cycle” an “PWM Period” can be specified via S-Registers.

This enables the user to either dim the brightness of an LED (PWM Period=0) or to specify blinking with

defined on-time in a defined period (PWM Period > blinking visible for the eye)

In LED_PULSE mode, the brightness of an LED is modulated. Modulation speed is defined by

parameter “Pulse Rate” and maximum brightness is defined by parameter “Duty Cycle”.

Bluetooth Profiles

This section covers S-Registers and AT-Commands that are related to the supported Bluetooth Profiles on the
BT-MM module.

1. Profile Server Activation

In order to advertise available services to potential client devices, S-Register 102 is used.

Supported profiles can be activated by setting the appropriate Flag in S-Register 102 (see Table 3 1).

After S-Register 102 has been written, all S-Registers must be saved to non-volatile memory (“AT&W”)

and subsequently a reset has to be carried out (“ATZ”).

2. A2DP

The “Advanced Audio Distribution Profile” is used to transmit high quality audio streams between

two Bluetooth devices. An A2DP role must be assigned to a BT-MM module, either source or sink.

After this has been done, the appropriate service can be advertised. An attempt to advertise

A2DP-service without prior set up of a role will result in a (new) response error code 46.

An incoming A2DP connection request is accepted automatically if a valid link key for the paging

device exists. If no link key is available, Secure Simple Pairing (SSP, BT2.1) or legacy pairing (BT2.0

or earlier) is carried out, depending on the Bluetooth Version of the paging device.

After an A2DP connection has been established, the module remains in AT Command mode.

S Register 531 is ignored for A2DP connections.

Table 3-5: LED S-Registers

TASK

AT-COMMAND / SREGISTER

COMMENT

Set LED_EXT0 mode

S335 [0..3], default=0

Mode:
0 = LED_OFF
1 = LED_ON
2 = LED_PWM
3 = LED_PULSE

Set LED_EXT1 mode

S340 [0..3], default=0

Set LED_EXT0 Duty Cycle

S336 [0..4095], default = 2048

referenced if LED mode = LED_PWM
or LED_PULSE

Set LED_EXT1 Duty Cycle

S341 [0..4095], default = 2048

Set LED_EXT0 PWM Period

S337 [0..15], default = 0

referenced if LED mode = LED_PWM

Set LED_EXT1 PWM Period

S342 [0..15], default = 0

Set LED_EXT0 Pulse Rate

S338 [0..15], default = 0

referenced if LED mode = LED_PULSE

Set LED_EXT1 Pulse Rate

S343 [0..15], default = 0

Содержание BTM511















































Результаты поиска

Содержание BTM511

Отзывы:

Похожие инструкции для BTM511

Бренды по названию

Популярные бренды

Laird BTM511, Руководство пользователя

Результаты поиска

Содержание BTM511

Отзывы:

Похожие инструкции для BTM511

Бренды по названию

Популярные бренды