Lafayette Parasol Accu-Rise Скачать руководство пользователя страница 18

Страница: 18 / 83

Parasol Installation Instructions

BACK

Cellular Window Shades

Auto-Lift

™

Installation Instructions

Thank you for choosing Parasol Cellular Shades. With proper installation and care,

your new shades will provide many years of beauty and performance.

Mounting Surface

Fastener

Wood

Drywall, Plaster

Metal

#6 Hex Head

Provided

Wall Anchors

Not Provided

Sheet Metal

Not Provided

Tools Needed

Power Drill, 1/4” Driver and drill bits

Tape Measure

Flat blade Screwdriver

Phillips Screwdriver

Pencil

Level

Shade Width

12” - 36”

36 1/16” - 72”

72 1/16” - 108”

108 1/16” - 144”

144 1/16” - 174”

Brackets Required

Installation

Brackets

Spacer

Blocks

Bottom Rail

Standard

Bottom-Up

Shade

Headrail

Low Mount

Battery Wand

Bracket (Optional)

Battery Pack Mounting Bracket Options

(Rear View)

High Mount

Battery Wand

Bracket (Standard)

Satellite Battery Pack or

DC Power Supply (Optional)

18V Battery

Wand with Battery

Wand Clip

DC Power Supply

Sensor Eye and

Manual Button

INSTALL THE BRACKETS

Outside Mount (A.)

- Center the headrail over the window opening at the

desired height and lightly mark each end on a flat

    mounting surface.
  - Mark 2” from each end of the headrail.
  - Center the installation brackets or extension brackets

on your marks and mount flush against the mounting

surface using the screws provided. Use drywall anchors

if necessary.

Inside Mount (B.)

- Measure 2” from each jamb for bracket location. If more

than two brackets came with your order, space

additional brackets evenly between the two and mark

their location. Allow a minimum of 15” between the

brackets at the motor end for the battery wand.

- Mount brackets using the screws provided. Be sure the

front edges of the brackets are aligned and level to

each other. Shim the brackets if necessary.

3/8” & 3/4”

Installation

Bracket

3/8” & 3/4”

End Mount

Brackets

1 1/4”

Installation

Bracket

1 1/4”

End Mount

Brackets

A. Outside Mount

B. Inside Mount

Note: Auto-Lift brackets will have spacer blocks already attached.

Содержание Parasol Accu-Rise




















































































Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды

Lafayette Parasol Accu-Rise, Руководство по установке

Результаты поиска

Содержание Parasol Accu-Rise

Отзывы:

Похожие инструкции для Parasol Accu-Rise

Бренды по названию

Популярные бренды