Labrie MINIMAX Скачать руководство пользователя страница 76

Страница: 76 / 174

Lubrication

Packer

Packer components that need to be lubricated include follower panel rollers and cylinder rear/front
pins. Use multipurpose grease (see

Recommended Lubricants

on page 57) to lubricate these

components as per the lubrication schedule.

Cylinder Pins

To lubricate the packer cylinder front pin:

Fully open the tailgate and install the tailgate safety prop.

Extend the cylinder in E

JECT

mode to get the front of the cutter blade out of the body.

Proceed with the locking out procedure. See

Locking Out and Tagging Out the Vehicle

on page 20.

Underneath the front of the cutter blade, locate the grease fitting of the cylinder front pin.

Apply lubricant.

Figure 4-15 Front pin grease fitting

To lubricate the packer cylinder rear pin:

Turn off the engine and disengage the hydraulic pump.

Proceed with the lockout procedure. See

Locking Out and Tagging Out the Vehicle

on page 20

Locate the remote grease fitting near the right-hand side clean-out door (see Figure 4-16).

This remote grease fitting consists of a hose going into the cylinder rear pin.

Apply lubricant with a grease gun.

Caution!

Before you proceed with lubrication, make sure all safety measures have been properly
taken.

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Labrie MINIMAX, Руководство по обслуживанию, Страница: 76 / 174

Результаты поиска

Содержание MINIMAX

Отзывы: