Labrie MINIMAX Скачать руководство пользователя страница 66

Страница: 66 / 174

Lubrication

Engine Oil

Refer to the engine manufacturer’s maintenance manual for recommended type of engine oil.

Transmission Oil

Refer to the transmission manufacturer’s maintenance manual for recommended type of
transmission oil.

Testing Hydraulic Oil

It is recommended to have hydraulic oil tested and analysed by a lab to prevent hydraulic system or
pump failures. This will also optimize the oil change frequency. Apply the following procedure to take
oil samples on Labrie vehicles.

OTE

The procedure may differ from other laboratories sample kits.

Preparing to Take a Sample

Before taking hydraulic oil samples:

Apply all safety measures to ensure safety around the vehicle at all times.

Start the engine and raise the body.

Install the body safety prop and lower the body onto it.

Disengage the pump and turn off the engine.

Locate the oil sample coupler. It is located behind the filter cover which is on top of the hydraulic
tank.

Caution!

Do not mix different brands of oil. In doubt, drain and refill with new oil.

Caution!

Highly contaminated hydraulic fluid must be changed promptly to avoid any damage on
the hydraulic system.

Содержание MINIMAX















































































































































































Результаты поиска

Содержание MINIMAX

Отзывы:

Labrie MINIMAX, Руководство по обслуживанию, Страница: 66 / 174

Результаты поиска

Содержание MINIMAX

Отзывы: