manualshive.com logo in svg

Labrie MINIMAX, Руководство по обслуживанию

Поделиться
Скачать
Labrie MINIMAX Скачать руководство пользователя страница 63

General Maintenance

55

To adjust the mid-height limit switch:

1.

Fully extend the arm.

2.

If not already done, raise the grabber to 90

 degrees.

3.

Turn off the engine. 

4.

Proceed with the tagout/lockout procedure. Refer to “Locking Out and Tagging Out the 
Vehicle” on page 20.

5.

Locate the mid-height limit switch at the base of the Helping-Hand

TM

 arm.

6.

Loosen the two screws indicated in Figure 3-39.

7.

Slide the limit switch forward or backward to achieve proper contact with the target.

8.

Tighten back up the screws.

9.

Test the operation.

10.

Repeat the procedure until the limit switch is properly adjusted.

N

OTE

:

The roller located at the front end of the limit switch must be vertically positioned. In case it is 
not, you will have to unscrew all 4

  screws that secure the front end to the rest of the switch, and 

turn the front end either clockwise or counterclockwise in order to position the roller 
vertically. Then replace all 4

 

screws and tighten them up.

I

MPORTANT

:

All limit switches MUST be working at all times. Otherwise, the operator may not be aware that the 
arm is not fully retracted or that the grabber is open or closed. This may cause an accident, 

injuries 

or property damages.

Danger!

Do not stand directly in the path of the arm while carrying out these tasks.

Содержание MINIMAX















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды